Light Conversion ORPHEUS Скачать руководство пользователя страница 19

Страница: 19 / 39

ORPHEUS User’s Manual

Light Conversion

[email protected]

NOTICE

Always make sure the USB control board is powered off
before connecting the extension cables.

Use only power supplies from Light Conversion. Power supply from Light Conversion is suitable to

both 110 V and 220

V outlets. Make sure that the main circuit board’s switch is in “

OFF

” position before

connecting the power supply.

WARNING

Always check that the supply and its cables are in proper
condition and do not show any damage to any part of the
insulation, before connecting.

It is recommended to install the WinTOPAS software before connecting ORPHEUS to computer.

Follow the instructions in the software start guide. Connect ORPHEUS to computer using supplied USB
cable.

Power LED (Red) should be always on and Status LED (Green) should blink with intervals of ~1 second

during normal operation of the USB control board. The software needs to be configured for a device,
hardware settings file must be linked in the software. Consult the WinTOPAS

user’s manual

on software

configuration.

A single computer can control up to 5 of the USB control boards. A USB-hub can be used if the

computer does not have enough USB ports. Light Conversion does not guarantee proper operation of
ORPHEUS with non-branded USB-hubs.

4.5

Input Beam Shutter

ORPHEUS is equipped with a stand-alone external shutter (see Figure 12a). Its primary purpose is to

enhance user safety while working with ORPHEUS. External shutter also safely dissipates the heat of the
input radiation.

Figure 12. Shutter external view from input side and principle of operation

Principle of operation relies on HR1030 mirror placed on a rotary solenoid. When the solenoid is not

powered (turned off), the mirror is directing the input beam sideward into the air-cooled or water-cooled

Содержание ORPHEUS








































Результаты поиска

Содержание ORPHEUS

Отзывы:

Похожие инструкции для ORPHEUS

Бренды по названию

Популярные бренды

Light Conversion ORPHEUS, Руководство пользователя

Результаты поиска

Содержание ORPHEUS

Отзывы:

Похожие инструкции для ORPHEUS

Бренды по названию

Популярные бренды