background image

Appendix E 

Repair and maintenance 

Introduction  

 

The PowerEase

®

 90W Power Supply requires no periodic maintenance program with the 

exception of an occasional dry wipe-down of the instrument. 

 

Encountering 

problems 

Check the troubleshooting section, see Appendix B 

Contact Technical Support, see Appendix F 

If the unit must be shipped back for repair, contact support for a Return Authorization 
Number and shipping instructions; see Appendix F 

 

Replace the fuse 

One extra fuse is supplies with the PowerEase

®

 90W Power Supply. For additional fuses, 

contact support; see Appendix F 

To replace the fuse: 

1.

 

Turn off the main power switch at the rear of the PowerEase

®

 90W Power Supply and 

detach the power cord from the rear of the PowerEase

®

 90W Power Supply. 

2.

 

Open the fuse compartment located inside the Power Inlet by inserting a small flat 

blade screwdriver into the slot on top of the fuse compartment. Turn the screwdriver 
to gently pry open the fuse compartment. 

Note

: The fuse compartment will not open with the power cord in place. 

3.

 

Pull the fuse holder out of the compartment and inspect the fuse. If the fuse is burned 
or there is a break in the fuse element, replace the fuse with an identical type of fuse 
(2A/250V). 

4.

 

Place the fuse holder back into the compartment. 

5.

 

Snap the cover closed. 
 

 

 

 

 

 
 

Fuse compartment 

Power inlet 

Power switch 

PowerEase

®

 90W Power Supply User Guide

  

 

17

 

 

Содержание PowerEase 90W





















Отзывы: