background image

4617000L

Copyright © Liberty Pumps, Inc. 2019 All rights reserved.

3 | EN

Safety Precautions

 

Accidental contact with electrically live parts, items, fluid, or 

water can cause serious injury or death.

 

Always disconnect the pump from power source before 

attempting to service the pump. Fatal electrical shock could 

occur.

 

The pump shall be plugged into a properly fused electrical 

outlet with a ground fault circuit interrupter (GFCI) that 

conforms to current National Electric Code (NEC) and all 

applicable local codes. All wiring must be performed by 

qualified personnel.

 

All electrical and safety practices shall be in accordance with 

the National Electrical Code

®

, the Occupational Safety and 

Health Administration, or applicable local codes and 

ordinances.

 

Pump shall be properly grounded using its supplied 

grounding conductor. Do not bypass grounding wires or 

remove ground prong from attachment plugs. Failure to 

properly ground the pump system can cause all metal 

portions of the pump and its surroundings to become 

energized.

 

Do not handle or unplug the pump with wet hands, when 

standing on damp surface, or in water unless wearing 

Personal Protective Equipment.

 

Always wear dielectric rubber boots and other applicable 

Personal Protective Equipment (PPE) when water is on the 

floor and an energized pump system must be serviced, as 

submerged electrical connections can energize the water. Do 

not enter the water if the water level is higher than the PPE 

protection or if the PPE is not watertight.

 

Do not lift or carry the pump by its power cord. This will 

damage the power cord, and could expose the electrically live 

wires inside the power cord.

 

The electrical power supply shall be located within the length 

limitations of the pump power cord, and for below grade 

installations it shall be at least 4 ft (1.22 m) above floor level.

 

Do not use this product in applications where human contact 

with the pumped fluid is common (such as swimming pools, 

fountains, marine areas, etc.).

 

Protect the power and control cords from the environment. 

Unprotected power and control (switch) cords can allow 

water to wick through ends into pump or switch housings, 

causing surroundings to become energized.

 

 

Do not use an extension cord to power the product. 

Extension cords can overload both the product and extension 

cord supply wires. Overloaded wires will get very hot and can 

catch on fire.

 

This product requires a separate, properly fused and 

grounded branch circuit, sized for the voltage and amperage 

requirements of the pump, as noted on the nameplate. 

Overloaded branch circuit wires will get very hot and can 

catch on fire. When used, electrical outlets shall be simplex of 

the appropriate rating.

 

Do not use this product with or near flammable or explosive 

fluids such as gasoline, fuel oil, kerosene, etc. If rotating 

elements inside pump strike any foreign object, sparks may 

occur. Sparks could ignite flammable liquids.

 

Sewage and effluent systems produce and may contain 

flammable and explosive gases. Prevent introduction of 

foreign objects into basin as sparks could ignite these gases. 

Exercise caution using tools and do not use electronic devices 

or have live, exposed electrical circuits in or around basins, 

open covers and vents.

 

These pumps are not to be installed in locations classified as 

hazardous in accordance with the National Electric Code

®

ANSI/NFPA 70.

 

 

Do not modify the pump/pump system in any way. 

Modifications may affect seals, change the electrical loading 

of the pump, or damage the pump and its components.

 

All pump/pump system installations shall be in compliance 

with all applicable Federal, State, and Local codes and 

ordinances.

 

Do not allow children to play with the pump system.

 

Do not allow any person who is unqualified to have contact 

with this pump system. Any person who is unaware of the 

dangers of this pump system, or has not read this manual, 

can easily be injured by the pump system.

 

Vent basin in accordance with local code. Proper venting of 

sewer and effluent gases alleviates poisonous gas buildup 

and reduces the risk of explosion and fire from these 

flammable gases.

 

Wear adequate Personal Protective Equipment when working 

on pumps or piping that have been exposed to wastewater. 

Sump and sewage pumps often handle materials that can 

transmit illness or disease upon contact with skin and other 

tissues.

 

Do not remove any tags or labels from the pump or its cord.

 

Keep clear of suction and discharge openings. To prevent 

injury, never insert fingers into pump while it is connected to 

a power source.

 

Do not use this product with flammable, explosive, or 

corrosive fluids. Do not use in a flammable and/or explosive 

atmosphere as serious injury or death could result.

 

This product contains chemicals known to the State of 

California to cause cancer and birth defects or other 

reproductive harm. www.p65warnings.ca.gov.

 

Do not dispose of materials such as paint thinner or other 

chemicals down drains. Doing so could chemically attack and 

damage pump system components and cause product 

malfunction or failure.

RISK OF ELECTRIC SHOCK

RISK OF FIRE

RISK OF SERIOUS INJURY OR DEATH

Содержание LowPro41LP









Отзывы: