LI-COR LI-7820 Скачать руководство пользователя страница 49

Страница: 49 / 92

Operating information

The bottom portion of the window provides more details about the instrument oper-
ating history and status.

Pump Operating Hours

is the number of hours that the pump has operated.

Pump Adjustment:

To fine-tune the pump drive voltage, which can remove oscil-

lations in data (if present). Choose a different pump speed and then review the
data stream.

Thermal Enclosure Temp

is the temperature of components inside the foam

insulating enclosure. If red, the instrument is either too hot and unable to reg-
ulate the enclosure temperature, or too cold and in a warmup state. Normally
this is between 51.5 °C and 57.5 °C.

Cavity Temperature

is the optical bench temperature. If red, the instrument is

either too hot and unable to regulate the cavity temperature, or too cold and in
a warmup state. Normally this is between 52 °C and 58 °C.

Laser Temperature

is the temperature of the diode laser. If red, the instrument

is unable to regulate the laser temperature.

Laser Temp. Shift

is the shift in the laser center wavelength from the factory cal-

ibration.

Ring Down Time

is a parameter indicating cavity resonance.

Device Uptime

shows the number of hours that the instrument has been

powered on.

On/Off cycles

is the number of times the instrument has been powered on.

Section 4. Software overview

4-13

Operating information

Содержание LI-7820





























































































Результаты поиска

Содержание LI-7820

Отзывы:

Похожие инструкции для LI-7820

Бренды по названию

Популярные бренды

LI-COR LI-7820, Инструкция по эксплуатации

Результаты поиска

Содержание LI-7820

Отзывы:

Похожие инструкции для LI-7820

Бренды по названию

Популярные бренды