background image

Maintenance Manual of Elevating Work Platform 

daily. 

!

Caution: Personal injury danger, 

i.e., leaking hydraulic oil can penetrate 
or burn skin. Wear goggles and 
protective gloves.

 

 

Leakage of high-pressure oil may be 
invisible to eyes, use cardboard or wooden 
boards as a search tool for hydraulic oil 
leakage. Hands shall be prohibited from 
being used for leakage confirmation. 
Inspect oil drops or residual oil on the 
following components: 

 

Hydraulic oil tank, filter, pump, hydraulic oil 
cylinder, motor, reduction gear, valve block 
and hydraulic tubing. 

 

Inspect oil drops or residual oil at the 
following areas: 

Rear of boom, fly jib, upper side of turntable, 
upper and lower sides of chassis, and ground 
underneath equipment. 

1)  Test or replace hydraulic oil every 2,000 h 

or every two years. 

 

!

Caution: If the oil isn’t replaced 

after the two year interval, it must be 
tested quarterly and replaced when it 
no longer passes the testing.

 

1)  Replace hydraulic oil suction filter, oil return 

filter and high pressure filter every 500 h or 
every  6  months.  Replace  oil  suction  filter, 
oil return filter and high pressure filter after 
first 50 h of use. It is necessary to replace 
the hydraulic filter to maintain performance 
and  service  life  of  the  machine.  Dirt  or  a 
clogged  filter  may  cause  performance 
degradation  of  hydraulic  components,  and 
continuous  use  will  cause  damage  to 
components.  In  dirty  work  environments  it 
is  necessary  to  increase  the  change 
intervals.

 

Use temperature

 

Oil type

 

The  lowest  temperature

L-HV  32  low  temperature 

-25

 

hydraulic oil 

 

-40

℃ <

The 

lowest 

temperature

-25

 

L-HS32 

ultra 

low 

temperature hydraulic oil

 

The  lowest  temperature

-40

 

10# aviation hydraulic oil

 

1.7  Check  for  Engine  Oil 
Level 

 

!

Do not operate on running 

engines! No smoking and open fires! 
Be careful when contacting with high 
temperature engine oil. Danger of 
scalding!

 

!

When operating on the oil system, 

pay attention to the surface cleaning. 
Carefully clean all areas involved. Blow 
wet parts with compressed air.

 

!

Please observe the safety 

regulations for engine oil and relevant 
local regulations. Dispose of spilled 
engine oil and filter elements as 
required. Waste oil cannot penetrate 
into the ground. 

!

Test run shall be carried out after 

each operation. At the same time, pay 
attention to the sealing and lubricating 
oil pressure, and then check the 
engine oil level.

 

Check the engine oil level every 8 hours or 
every day. 

Insufficient  or  excessive  engine  oil  may  cause 

Содержание T20J




































Отзывы: