LG WM1812CW Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 37

LG WM1812CW Скачать руководство пользователя страница 16

15

ERROR SYMPTOM

CAUSE

OVER

CURRENT

ERROR

• MAIN PWB ASSEMBLY is out of order.

• Winding in the STATOR ASSEMBLY is short-circuited.

• The connector (3-pin, male, white) in the MOTOR

HARNESS is not connected to the connector
(3-pin, female, white) of STATOR ASSEMBLY.

• The electric contact between the connectors

(3-pin, male, white) in the MOTOR HARNESS
and 4-pin, female, white connector in the MAIN PWB
ASSEMBLY is bad or unstable.

• The MOTOR HARNESS between the STATOR

ASSEMBLY and MAIN PWB ASSEMBLY is cut (open
circuited).

• The hall sensor is out of order/defective.

8

9

LOCKED

MOTOR

ERROR

• Loose Ball Sensor Connector.
• Ball Sensor is out of order.

※

Displayed only when the START/PAUSE button is first
pressed in the QC Test Mode.

10

BALL SENSOR

ERROR

• The washer experienced a power failure.

12

POWER

FAILURE

• EEPROM is out of order.

※

Displayed only when the START/PAUSE button is first
pressed in the QC Test Mode.

11

EEPROM

ERROR

«
...
14
15
16
17
18
...
»

Содержание WM1812CW






































Отзывы:

Нет отзывов