LG VX5400 Скачать руководство пользователя страница 13

Страница: 13 / 171

2. Installation

2.1 Installing a Battery Pack

1) The Battery pack is keyed so it can only fit one way. Align the groove in the battery pack with the rail on the

back of the phone until the battery pack rests flush with the back of the phone.

2) Slide the battery pack forward until you hear a “click”, which locks the battery in place.

2.2 For Adapter Use

1) Plug the adapter into a wall outlet. The adapter can be operated from a 110V source. When AC power is

connected to the adapter.

2) Insert the adapter jack into the phone with the installed battery pack.

Red light indicates battery is being charged.. Green light indicates battry is fully charged.

2.3 For Mobile Mount

2.3.1 Installation Position

In order to reduce echo sound when using the Hands-Free Kit, make sure that the speaker and microphone are

not facing each other and keep microphone a generous distance from the speaker.

2.3.2 Cradle Installation

Choose an appropriate flat surface where the unit will not interface with driver’s movement or passenger’s

comfort. The driver/user should be able to access the phone with ease. Using the four self-tapping screws

provided, mount the supplied braket on the selected area. Then with the four machine screws provided, mount

the counterpart on the reverse side of the reverse side of the cradle. Secure the two brackets firmly together by

using the two bracket joint screws provide. The distance between the cradle and the interface box must not

exceed the length of the main cable.

2.3.3 Interface Box

Choose an appropriate flat surface ( somewhere under the dash on the passenger side is preferred ) and mount

the IB bracket with the four self-tapping screws provided. Clip the IB into the IB bracket.

2.3.4. Microphone Installation

Install the microphone either by clipping I onto the sunvisor (driver’s side) or by attaching it to door post

(driver’s side), using a velcno adhesive tape (not included).

Only for training and serving purposes

- 13 -

Z3X-BOX.COM

Содержание VX5400









































































































































































Результаты поиска

Содержание VX5400

Отзывы:

Похожие инструкции для VX5400

Бренды по названию

Популярные бренды

LG VX5400, Руководство по обслуживанию

Результаты поиска

Содержание VX5400

Отзывы:

Похожие инструкции для VX5400

Бренды по названию

Популярные бренды