LG SolarDOM MP-9486SC страница 29 Скачать руководство пользователя

Страница: 29 / 39

5-19

(TROUBLE 7) Heater Relay 5- Up. sheath Heater

Relay 6- Lo. sheath Heater
Relay 7- H Ceramic Heater

CONDITION

CHECK

RESULT

CAUSE

REMEDY

1. Heater is not

operating.

Abnormal.

Normal.

Heater.

Thermostat and
relay 5, 6, 7.

Abnormal.

Malfunction of the
thermostat and
relay 5, 6, 7

Malfunction of the
heater.

Replace.

Wire connection.

No continuity.

Open or loosen.

Replace or
connect tightly.

Replace.

2. Lower tempera-

ture the oven.

Abnormal.

Normal.

Heater.

Thermostat and
relay 5, 6, 7.

Abnormal.

Malfunction of the
thermostat and
relay 5, 6, 7

Malfunction of the
heater.

Replace.

(TROUBLE 6) Oven does not cook properly when programmed for the set power level

(Operates properly on HIGH)

CONDITION

CHECK

RESULT

CAUSE

REMEDY

Output is full when

you set lower
power level.

Abnormal.

Disconnect the
wire leads from
relay 4 and check
continuity relay 4.
(Operate the unit)

Defective P.C.B.
assembly.

Replace P.C.B.
assembly.

NOTE:

* Make sure the wore leads are in the correct position.

* When removing the wire leads from parts, Be sure to grasp the connector not the wires.
* When removing the magnetron, be sure to install the magnetron gasket in the correct position and in

good condition.

Содержание SolarDOM MP-9486SC








































Результаты поиска

Содержание SolarDOM MP-9486SC

Отзывы:

Похожие инструкции для SolarDOM MP-9486SC

Бренды по названию

Популярные бренды

LG SolarDOM MP-9486SC, Руководство по обслуживанию

Результаты поиска

Содержание SolarDOM MP-9486SC

Отзывы:

Похожие инструкции для SolarDOM MP-9486SC

Бренды по названию

Популярные бренды