background image

Owner's Manual 

19

Maintenance and Service

ENGLISH

Clean the unit with a soft dry cloth. Do not use bleach or abrasives.

Never use any of these 
• Water hotter than 40°C. It may cause deformation and discoloration.
• Volatile substances. They may damage the surface of the air conditioner.

Air Filters

To remove the filters see the self explanatory diagrams for each 
model type. Clean the filters with a vacuum cleaner or warm soapy
water. If dirt is not easily removed, wash with a solution of detergent 
in luke warm water. Dry well in shade after washing and reinstall the
filters back in place.
When thinking about buying a new Air Filter, Please contact your
dealer/serviceman

Deodorizer Filters

Remove the deodorizer filters behind the air filter and expose them in 
direct sunlight for 2 hours. 
And then insert these filters into original position.

Dust Box

The dust box should be cleaned every 3 years.
(The capacity of the dust box is designed to collect the amount of dust accumulated at the air conditioner
filter for 5 years based on the general house.)

Gasoline

Powder

Maintenance and Service

Indoor Unit

Before performing any maintenance, turn off the main power to the system, disconnect the circuit breaker and 
unplug the power cord.

Содержание S09AA























Отзывы: