![background image](http://html.mh-extra.com/html/lg/rp-29fa40-m/rp-29fa40-m_service-manual_1903529014.webp)
FACTORY MENU (continued)
FA - INSTALLERS MENU
2-2
21 Horz AFC:
Set the automatic horizontal frecuency con-
trol on, should be 1.
22 WPL:
Activates White Peak Limiter
23 Tint Offset:
Set the Tint offset
24Red Cut:
Set the Red Cutoff of Low Luminance White
Balance adjustment
25Green Cut:
Set the Green Cutoff of Low Luminance
White Balance adjustment
26Blue Cut:
Set the Blue Cutoff of Low Luminance White
Balance adjustment
27Green Gain:
Set the Green Gain of High Luminance
White Balance adjustment
28Blue Gain:
Set the Blue Gain of High Luminance White
Balance adjustment
29Air AFT:
Set the AFT when watching air signal.
30 A ATT:
Adjust the composite input level to the audio
decoder to have the standard input level.
31 A VCO:
Adjust Stereo VCO and SAP VCO free running
frequency.
32 A Filter:
Adjust the filter for Stereo, SAP and DBX.
33 A Spectral:
Adjust high frequency stereo separation
(3KHz.)
34 Wide Band:
Adjust low frequency stereo separation
(300Hz.)
35 Max Blk. Hrs:
Adjust the maximun number of hours
the TV can remain Blocked (even 99 hours)
36RGB Contrast:
Set OSD Contrast level
37SUB Contrast:
Set internal Sub-Contrast Register
38 EW Correct:
East- West Correction. Range 0-63, Ini-
tial value:26
39 EW Top-Corr
East-West Corner Correction (top). Range
0-31, Initial value: 14
40 EW Bott-Corr:
East-West Corner Correction (bottom).
Range 0-31, Initial value: 23
41 EW Trap-Corr:
East-West Trapezium Correction.Range
0-63. Initial value 30. Range 0-31, Initial value: 23
42 V Centering:
Vertical Centering. Range 0-63. Initial
value: 30
43 V Linearity:
Vertical Linearity. Range 0-15. Initial
value: 12
44 V S-Corr:
Vertical S-Correction. Range 0-15. Initial
value: 11
45 H EHT Comp:
Horizontal Extremely High Tension
Compesation. Range 0-7. Initial value: 4
46 V EHT Comp:
Vertical Extremely High Tension
Compesation. Range 0-7. Initial value: 6
47DC Rest
Set the DC Restoration level
48BLK Stretch
Set the Black Stretch start point
49ABL Gain
Set the Automatic Black Level Gain
50SVM GAIN
Adjust the Scan Velocity Modulator gain
51SVM PH
Adjust the Scan Velocity Modulator Phase
52ACB SW
Activates Automatic Control Beam
53SHARP PF
Sharpness peak frequency selection: 0 to
3.2 MHz and 1 to 4.0 MHz
54CORING
Activates the enhancement of Sharpness from
1 to 2 MHz
55B-Y ATT
Set the attenuation level of Cb of YUV signal
56R-Y ATT
Set the attenuation level of Cr of YUV signal
57AUTO FLESH
Activates the Flesh tone control
58 ABL START POINT
Set the Automatic Black Level Start
Point
59Y GAMMA
Set the non-linear Gamma curve for Lumi-
nance signal
60ACB PULSE
P Set Automatic Control Beam Start Point
61SCREEN
Not used
62AKB SETUP
Mute the RGB Cathodes
63AUX BAND PASS
Activates the Band Pass Filter for
Auxiliar (Composite, Y/C, YUV) input
64CD MATRIX
Set the relative phase and amplitude of
Color response to demodulate de Chroma
65YCbCr
Select the Demodulation System for Component
Video YUV or YCbCr
66C GAMMA
Switch the Color Gamma
Содержание RP-29FA40-M
Страница 40: ...P NO 3828VD0097A April 2001 ...