LG RCT689H Скачать руководство пользователя страница 28

Страница: 28 / 165

3-9

VCR ELECTRICAL TROUBLESHOOTING GUIDE

3. SERVO CIRCUIT

3-1. Unstable Video in PB MODE

3-2. When the Drum Motor
doesn’t run.

YES

Do the

CTL pulses appear at

IC501 Pin76?

YES

Does 12V

appear at PMC01

Pin8?

YES

Does 2.8V

appear at PMC01

Pin12?

Do the

Drum PWM Pulses

appear at the IC501

Pin34?

Do the

DFG Pulses appear at

IC501 Pin65?

Is adjusting the height of

the CTL Head accurate?

Readjust the height of the

CTL Head.

YES

When the Drum Motor

doesn’t run,

Does the Noise level of the

screen change periodically?

YES

On tracking

do the CTL pulses

move?

Replace IC501.

Do the

DFG Pulses appear at

PMC01 Pin11?

Refer to “(2) No 12VA of

Power section”

Aren’t the foil patterns and

the Components between

IC501 Pin34 and PMC01

Pin12 shorted?

Are the connecting patterns and the Components

between IC501 Pin34 and PMC01 Pin12 shorted?

Replace the Cap M.

Aren’t the foil patterns and

the Components between

IC501 Pin65 and PMC01

Pin11 shorted?

Do the

Drum PWM Pulses

appear at IC501

Pin34?

YES

Replace IC501.

YES

Does the

Video Envelope waveform

appear at IC501

Pin82?

Refer to “When the Y signal

doesn’t appear on the

screen in PB Mode”.

Does the CFG waveform

appear at IC501 Pin67?

Replace IC501.

Check the connector

(PMC01) and the

Drum Motor Ass’y.

Содержание RCT689H






































































































































































Результаты поиска

Содержание RCT689H

Отзывы:

Похожие инструкции для RCT689H

Бренды по названию

Популярные бренды

LG RCT689H, Руководство по обслуживанию

Результаты поиска

Содержание RCT689H

Отзывы:

Похожие инструкции для RCT689H

Бренды по названию

Популярные бренды