LG OK99 Скачать руководство пользователя страница 48

Страница: 48 / 85

3-23

Only for training and service purposes.

ONE POINT REPAIR GUIDE

NO SOUND

There is no sound output in the Bluetooth function, repair the set according to the following guide.

10-5. BLUETOOTH FUNCTION

10-5-1. Solution

Replace IC501 on the MAIN board or B/T module on the Front Panel.

10-5-2. How to troubleshoot (Countermeasure)

1) Check BT_RX, BT_TX signal to pin4, 6 of CN504.



If no signal, check the signal to pin4, 6 and pin10(3.3 VA) of on the bluetooth module and cable

connection state.



If there are no signal out from module, replace new module.

2) Check if BT_RX/TX is entered from pin4, 6 of CN504 to pin K1, L1 to IC501 (DSP).
3) Check if MCS_BCK, MCS_LRCK & MIX_DATAN is entered from IC501 to IC601.



If no signal, check 1.2 VA for IC501.



If it is abnormal, change replace it a new one.

4) Check the following I2S signal flow from IC501 to IC601.



If there is any trouble, check the power for each IC.



If the signals are abnormal, replace it a new one.

5) Check if the digital audio AMP block is okay. Refer to “Digital Audio AMP” guide.



If AMP is damaged, replace it with a new one.

10-5-3. Service hint (Any picture / Remark)

IC501

IC601

PWM

MCS_BCK

MCS_LRCK
MIX_DATA_OUT

IR AMP

B/T Module

BT_RX,
BT_TX

< Bluetooth function signal

ow >

< MAIN board bottom view >

< MAIN board top view >

CN504

IC601

MIX_DATA2_OUT

MIX_DATA2_OUT
MIX_DATA0_OUT

MIX_DATA0_OUT

MCS_LRCK

MCS_BCK

BT_RTS. pin 7

BT_RTS. pin 7
BT_CTS. pin 8

BT_CTS. pin 8

BT_RX. pin 6

BT_TX. pin 4

Содержание OK99












































































Результаты поиска

Содержание OK99

Отзывы:

Похожие инструкции для OK99

Бренды по названию

Популярные бренды

LG OK99, Руководство по обслуживанию

Результаты поиска

Содержание OK99

Отзывы:

Похожие инструкции для OK99

Бренды по названию

Популярные бренды