manualshive.com logo in svg

LG MultiSITE MS8000 Series, Руководство по установке, Страница: 14 / 24

Поделиться
Скачать
LG MultiSITE MS8000 Series Скачать руководство пользователя страница 14

14

MultiSITE MS8000 Series Room Controllers

Due to our policy of continuous product innovation, some specifications may change without notification.  

©LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG Life’s Good” is a registered trademark of LG Corp.

Figure 5: Wiring - Single or Multispeed Motor.

Figure 6: BO8 Auxiliary Output Wiring.

All electric work must be performed by a licensed electrician and conform to local building codes or, in the absence of local 

codes, with the National Electrical Code, and the instructions given in this manual.

If the power source capacity is inadequate or the electric work is not performed properly, it may result in fire, electric shock, physical injury or death.

HIGH

HIGH

MED

LOW

LOW

HIGH

HIGH

HIGH

MED

LOW

LOW

HIGH

3 Speed

2 Speed

Single Speed

24 Vac  

Transformer

Power and Fan

Figure 7: Wiring - ECM Motor.

Power and Fan

Relay Coil

Wiring ECM Motor

BO4 - Fan H

 

RC (24 Vac)

C (Common)

UO10 ECM Fan 

24 Vac Transformer

0 - 10 Vdc signal

24 Vac signal to start fan (optional)

4

+

-

Power and Fan

Relay Coil

RC (24 Vac)

C (Common)

RH

BO8 - Aux Heat

R

RC (24 Vac)

C (Common)

RH

BO8 - Aux Heat

R

24 Vac Power to Relay

Dry Contact to End Device 24 Vac ~Maximum

WIRING FOR MS8350

Wiring

Содержание MultiSITE MS8000 Series

























Отзывы:

Нет отзывов