LG MS2647GR Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 34

background image

5-4

D. DOOR GROSS ASSEMBLY REMOVAL

1) Open the door.
2) Remove the choke cover very carefully with a flat-

blade screwdriver.

CAUTION : Be careful not to damage door seal plate

by screwdriver.

3) Lift up and push the door.

NOTE:

1. After replacing the door, be sure to check that the

primary switch, monitor switch, and secondary switch
operate normally.

2. After replacing the door, check for microwave energy

leakage with a survey meter. Microwave energy must
be below the limit of 5 mW/cm

2

. (with a 275 ml water

load)

3. When mounting the door assembly to the oven

assembly, be sure to adjust the door assembly parallel
to the chassis. Also adjust so the door has no play
between the inner door surface and oven frame
assembly. If the door assembly is not mounted
properly, microwaves may leak from the clearance
between the door and the oven.

E. HIGH VOLTAGE TRANSFORMER

REMOVAL

1) Discharge the high voltage capacitor.
2) Disconnect the leadwire from magnetron, high voltage

transformer, and capacitor.

3) Remove the screw holding the high voltage

transformer to the baseplate.

F. FAN MOTOR ASSEMBLY REMOVAL

1) Discharge the high voltage capacitor.
2) Disconnect the leadwire from fan motor, fuse board

and high voltage capacitor.

3) Remove the two screws holding the the suction guide

ASS’Y to the oven cavity and remove the high voltage
diode earth screw.

4) Remove the screw of the capacitor bracket.
5) Remove the two screws holding the fan motor ASS’Y

to the suction guide ASS’Y.

G. HIGH VOLTAGE CAPACITOR AND

DIODE REMOVAL

1) Discharge the high voltage capacitor.
2) Disconnect the leadwire from fan motor, fuse board

and high voltage capacitor.

3) Remove the screw holding the suction guide ASS’Y to

the oven cavity and remove the high voltage diode
earth screw.

4) Remove the screw holding the high voltage capacitor

bracket.

H.V.
Diode

H.V.
Capacitor

Suction
Guide

H.V.
Transformer

Remove choke cover

LGE Internal Use Only

Copyright © 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes

«
...
12
13
14
15
16
...
»

Содержание MS2647GR



































Отзывы:

Нет отзывов

Похожие инструкции для MS2647GR

Бренд: NEFF Страницы: 29

Бренд: Kasanova Страницы: 62

Бренд: Jenn-Air Страницы: 53

Spacemaker JNM1541DN

Бренд: GE Страницы: 3

Бренд: Brandt Страницы: 23

Бренд: CDA Страницы: 12

Бренд: Insignia Страницы: 21

Бренд: Daewoo Страницы: 23

Бренд: Falcon Страницы: 4

Бренд: Hotpoint Страницы: 16

Бренд: Tappan Страницы: 14

Бренд: montpellier Страницы: 17

Бренд: Jocel Страницы: 62

Бренд: Charmate Страницы: 28

Combi TOUCH Series

Бренд: Electrolux Страницы: 68

Бренд: Electrolux Страницы: 64

Бренд: Electrolux Страницы: 40

Бренд: Bosch Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды