manualshive.com logo in svg

LG MS-256NB, Руководство по обслуживанию

Поделиться
Скачать
LG MS-256NB Скачать руководство пользователя страница 18

5-8

CAUTIONS

1. DISCONNECT THE POWER SUPPLY CORD FROM THE OUTLET WHENEVER REMOVING THE

OUTER CASE FROM THE UNIT. PROCEED WITH THE TEST ONLY AFTER DISCHARGING THE HIGH
VOLTAGE CAPACITOR AND REMOVING THE WIRE LEADS FROM THE PRIMARY WINDING OF THE
HIGH VOLTAGE TRANSFORMER. (SEE PAGE 2-1)

2. ALL OPERATIONAL CHECKS WITH MICROWAVE ENERGY MUST BE DONE WITH A LOAD (1 LITER

OF WATER IN CONTAINER) IN THE OVEN.

COMPONENTS

TEST PROCEDURE

RESULTS

HIGH VOLTAGE
TRANSFORMER
(Wire leads removed)

MAGNETRON
(Wire leads removed)

1. Measure the resistance.

(Ohm-meter scale: Rx1)
• Primary winding
• Secondary winding
• Filament winding

2. Measure the resistance.

(Ohm-meter scale: Rx1000)
• Primary winding to ground
• Filament winding to ground

1. Measure the resistance.

(Ohm-meter scale: Rx1)
• Between Filament terminal

2. Measure the resistance.

(Ohm-meter scale: Rx1000)
• Filament to chassis

Approx.: 1.4 

Ω

Approx.: 90 

Ω

Less than: 0.1 

Ω

Normal: 

∞

Normal: 

∞

Normal: Less than 1 

Ω

Normal: 

∞

PRIMARY  
TERMINAL

SECONDARY  
WINDING

FILAMENT 
WINDING
TERMINAL

COMPONENT TEST PROCEDURE

Содержание MS-256NB




































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды