manualshive.com logo in svg

LG MS-2384B, Руководство пользователя

Поделиться
Скачать
LG MS-2384B Скачать руководство пользователя страница 23

5-13

(TROUBLE 2) Oven does not operate at all ; Display window does not display any figures and

no input is accepted.

CONDITION

CHECK

RESULT

CAUSE

REMEDY

NOTE : All these switches must be replaced at the same time. Refer to page 5-6, 5-7

2. Fuse does not

blow.

No continuity.

Continuity.

Check continuity
of power supply
cord.

Defective power
supply cord.

Replace power
supply cord.

Defective mag-
netron thermostat.

Replace mag-
netron thermostat.

Check continuity
of magnetron
thermostat.

No continuity.

1. Fuse blows.

Continuity.

Malfunction of the
monitor switch.

Replace primary
and monitor
switches.

Check continuity
of monitor
switch (with
door closed).

Check continuity
of primary
switch (with
door opened).

No continuity.

Disconnect one
side of the wire
lead connected
from transformer
to the high
voltage
capacitor and
operate the unit.

No continuity.

Continuity.

Shorted contact at
the primary switch.

Replace primary
and monitor
switches.

Fuse blows again

Normal.

Defective high
voltage capacitor.

Replace high
voltage capacitor.

Defective high volt-
age transformer.

Replace high volt-
age transformer.

Replace fuse

Содержание MS-2384B



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды