background image

INSTALLATIONS

3-1

INSTALLING

1. Empty the microwave oven and clean inside it with

a soft, damp cloth. Check for damage such as
misaligned door, damage around the door or dents
inside the cavity or on the exterior.

2. Put the oven on a counter, table, or shelf that is

strong enough to hold the oven and the food and
utensils you put in it. (The control panel side of the
oven is the heavy side. Use care when handling.)

3. Do not block the vent and the air intake openings.

Blocking vent or air intake openings can cause
damage to the oven and poor cooking results.
Make sure the microwave oven legs are in place to
ensure proper air flow.

4. The oven should not be installed in any area where

heat and steam are generated, because they may
damage the electronic or mechanical parts of the
unit.
Do not install the oven next to a conventional
surface unit or above a conventional wall oven.

5. Use microwave  oven in an ambient temperature

less than 104°F(40°C).

6. Place the microwave  oven on a sturdy and flat

surface at least 10 cm(4 inches) from the wall.

7. Place the microwave oven as far away as possible

from TV, RADIO, COMPUTER, etc., to prevent
interference.

EARTHING INSTRUCTIONS

This microwave oven is designed to be used in a fully
earthed condition.
It is imperative, therefore, to make sure it is properly
earthed before servicing

WARNING-
THIS APPLIANCE
MUST BE EARTHED

IMPORTANT

As the colors of the wires in the mains lead of this
appliance may not correspond with the colored
markings identifying the terminals in your plug,
proceed as follows.

The wire which is colored 

green-and-yellow

must be

connected to the terminal in the plug which is marked
with the letter 

E

or by the 

earth symbol

(    ) or

colored 

green

or 

green-and-yellow

.

The wire which is colored 

blue

must be connected to

the terminal in the plug which is marked with the letter

N

or colored 

black

.

The wire which is colored 

brown

must be connected

to the terminal in the plug which is marked with the
letter 

L

or colored 

red

.

BEFORE YOU BEGIN, READ THE FOLLOWING INSTRUCTIONS COMPLETELY AND CAREFULLY.

10cm

The wires in this mains lead are colored in
accordance with the following code:

Green-and-yellow:

Earth

Blue:

Neutral

Brown:

Live

Содержание MS-1904H





















Отзывы: