manualshive.com logo in svg

LG MH-704A, Руководство по обслуживанию

Поделиться
Скачать
LG MH-704A Скачать руководство пользователя страница 21

5-14

CONDITION

CHECK

RESULT

CAUSE

REMEDY

1. Fuse blows.

Continuity.

No continuity.

Continuity.

Shorted contact at
the primary switch.

Replace primary
and monitor
switches.

No continuity.

Normal.

Defective high
voltage capacitor.

Replace high
voltage capacitor.

Fuse blows again

Defective high volt-
age transformer.

Replace high volt-
age transformer.

Malfunction of the
monitor switch.

Replace primary
and monitor
switches.

Check continuity
of monitor
switch (with
door closed).

Check continuity
of primary
switch (with
door opened).

Disconnect one
side of the wire
lead connected
from transformer
to the high
voltage
capacitor and
operate the unit.

Replace fuse

(TROUBLE 2) Oven does not operate at all ; Display window does not display any figures and   

no input is accepted.

NOTE : All these switches must be replaced at the same time. Refer to page 5-6, 5-7

2. Fuse does not

blow.

No continuity.

No continuity.

Replace power
supply cord.

Defective mag-
netron thermostat.

Defective power
supply cord.

Replace mag-
netron thermostat.

Check continuity
of magnetron
thermostat.

Check continuity
of power supply
cord.

Continuity.

Содержание MH-704A
































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды