LG MG-553MD Скачать руководство пользователя | Manualshive

Страница: 11 / 18

background image

5-10

COMPONENTS

TEST PROCEDURE

RESULTS

FUSE

HEATER ELEMENT
(Wire leads removed.)

GRILL THERMOSTAT

OVEN THERMOSTAT
MAGNETRON
THERMOSTAT

Check for continuity of the fuse with an
multi-meter.

NOTE: If the fuse is blown, check the primary, the secondary, and the monitor
switches, H.V.D. and H.V.C. before replacing the fuse.
If the fuse is blown by improper switch operation replace the defective switch
and the fuse at the same time. Replace just the fuse if the switches operate
normally.

NOTE: Make sure heater is fully cooled when tested.

Measure the resistance.
(Multi-meter scale: Rx1)

Normal:
*Grill heater

Approx. 38 ohm
(at 20 ~ 30

o

C)

Normal: more than 0.5 Mohm

Normal Abnormal

Measure the resistance with 500V-100M ohm
insulation resistance meter.

0°C~Approx.90°C Approx.90°C

0°C~Approx.145°C Approx.145°C

«
...
9
10
11
12
13
...
»

Содержание MG-553MD



















Отзывы:

Нет отзывов

Похожие инструкции для MG-553MD

Бренд: Zanussi Страницы: 16

TSSTTV-ELXLDAF3

Бренд: Oster Страницы: 17

Бренд: Kuppersbusch Страницы: 52

Бренд: CDA Страницы: 20

Бренд: Viking Страницы: 2

Бренд: Verona Страницы: 24

Бренд: Daewoo Страницы: 36

Бренд: NEFF Страницы: 44

Бренд: Daewoo Страницы: 39

Бренд: Nectre Fireplaces Страницы: 16

Бренд: Zanussi Electrolux Страницы: 36

Бренд: Kuppersbusch Страницы: 28

Бренд: Tisira Страницы: 28

Бренд: Venini Страницы: 13

Ultra-Max UM1854-LP

Бренд: Holman Страницы: 44

Бренд: Bauknecht Страницы: 84

Бренд: NutriMill Страницы: 16

Бренд: Samsung Страницы: 433

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды