LG MB3949G Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 34

background image

5-8

CAUTIONS

1. DISCONNECT THE POWER SUPPLY CORD FROM THE OUTLET WHENEVER REMOVING THE

OUTER CASE FROM THE UNIT. PROCEED WITH THE TEST ONLY AFTER DISCHARGING THE HIGH
VOLTAGE CAPACITOR AND REMOVING THE WIRE LEADS FROM THE PRIMARY WINDING OF THE
HIGH VOLTAGE TRANSFORMER. (SEE PAGE 2-1)

2. ALL OPERATIONAL CHECKS WITH MICROWAVE ENERGY MUST BE DONE WITH A LOAD (1 LITER

OF WATER IN CONTAINER) IN THE OVEN.

COMPONENTS

TEST PROCEDURE

RESULTS

HIGH VOLTAGE
TRANSFORMER
(Wire leads removed)

MAGNETRON
(Wire leads removed)

1. Measure the resistance.

(Ohm-meter scale: Rx1)
• Primary winding
• Secondary winding
• Filament winding

2. Measure the resistance.

(Ohm-meter scale: Rx1000)
• Primary winding to ground
• Filament winding to ground

1. Measure the resistance.

(Ohm-meter scale: Rx1)
• Filament terminal

2. Measure the resistance.

(Ohm-meter scale: Rx1000)
• Filament to chassis

Approx.: 1.4 ohm
Approx.: 90 ohm
Less than: 1 ohm

Normal: Infinite
Normal: Infinite

Normal: Less than 1 ohm

Normal: Infinite

PRIMARY
TERMINAL

SECONDARY
WINDING

FILAMENT
WINDING
TERMINAL

COMPONENT TEST PROCEDURE

LGE Internal Use Only

Copyright © 2007 LG Electronics. Inc. All right reserved.
Only for training and service purposes

«
...
16
17
18
19
20
...
»

Содержание MB3949G



































Отзывы:

Нет отзывов

Похожие инструкции для MB3949G

Бренд: Adexa Страницы: 7

Бренд: Haier Страницы: 24

Бренд: Vega Страницы: 46

Бренд: Garland Страницы: 32

Бренд: Garland Страницы: 2

Бренд: Garland Страницы: 32

Бренд: Oster Страницы: 17

Бренд: MAISTERmicro Страницы: 38

Бренд: Magic Chef Страницы: 45

Бренд: Monsher Страницы: 76

Бренд: Maier Страницы: 96

Бренд: Gourmia Страницы: 20

Бренд: Zanussi Electrolux Страницы: 36

Бренд: DRIVEN Страницы: 36

Бренд: Hyundai Страницы: 31

Бренд: Daewoo Страницы: 38

Бренд: Gaggenau Страницы: 56

Бренд: Samsung Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды