background image

Safety Precautions   

6

Ventilator

CAUTION

Keep level even when
installing the prod-
uct. 

• To avoid vibration or

water leakage.

Use two or more peo-
ple to lift and trans-
port the product. 

• Avoid personal injury.

Do not install the
product where it will
be exposed to sea
wind (salt spray)
directly.

• It may cause corrosion

on the product. Corro-
sion, particularly on the
condenser and evapora-
tor fins, could cause
product malfunction or
inefficient operation.

Don't connect the
ground wire to the win-
dow frame or water
cock. 

• There is risk of electric

shock.

Do not install the prod-
uct at a smoky and oily
place like kitchen or
factory.

• Otherwise. oil may

adhere to the filter or
heating exchanger and
cause trouble.

Install the product in
an insulated space
from outdoor air.

• In case of installing the

product outside of the
insulated layer, dewing
occurs inside of the
main body in winter.And
it causes electrical
shock or falling of con-
densed water.

n

Installation

The outside ducts must be tilted
at a gradient (1/30 or more) down
toward the outdoor area from the
ventilator unit, and properly insu-
lated. (The entry of rain water may
cause power leaks, fire or damage
to household property.)

Glove should be worn when doing
the installation work. (There is
risk of injury.)

Содержание LZ-H025GBA3




























Отзывы: