LG LWHD1200R Скачать руководство пользователя страница 9

Страница: 9 / 38

Service Manual 9

Installation

Suggested Tool Requirements

SCREWDRIVER (+, -), RULER, KNIFE, HAMMER, PENCIL, LEVEL

Preparation of Chassis

1. Remove the screws that fasten the cabinet at both

sides and at the back.

2. Slide the unit out from the cabinet by gripping the

base pan handle and pulling forward while

bracing the cabinet.

3. Cut the window sash seal to the proper length. Peel

off the backing and attach the Foam-Pe

to the

underside of the window sash.

4. Remove the backing from the top upper guide

Foam PE

and attach it to the bottom of the Upper

Guide

5. Attach the upper guide onto the top of the cabinet

with 3 type A screws.

6. Insert the Frame Guides

into the bottom of the

cabinet.

7. Insert the Frame Curtain

into the upper guide

and Frame Guides

8. Fasten the curtains to the unit with 4 Type A screws

at the both sides.

Cabinet Installation

1. Open the window. Mark a line on center of the win-

dow stool (or desired air conditioner location).
Carefully place the cabinet on the window stool and
align the center mark on the front angle with the
center line marked in the window stool.

2. Pull the bottom window sash down behind the

upper guide until it meets.

Do not pull the window sash down so
tightly that the movement of Frame
Curtain

is restricted.

NOTICE

Shipping
Screws

(Type A)

EPS Material

Upper Guide

Window stool

Front Angle

Window Sash

Upper guide

Frame Curtain

Foam-pe

Cabinet

˚C

TEM

F1 LO

F2 M

F3 H

Dry

Tim

Fan

Ene

rgy

Sav

TIM

FAN

SPE

˚C

TEM

F2 M

Dry

Tim

Fan

Ene

rgy

Save

TIM

FAN

SPE

˚C

TEM

F1 L

Dry

Tim

Fan

Ene

rgy

Sav

TIM

FAN

SPE

Figure 2

Figure 3

Содержание LWHD1200R







































Результаты поиска

Содержание LWHD1200R

Отзывы:

Похожие инструкции для LWHD1200R

Бренды по названию

Популярные бренды

LG LWHD1200R, Руководство по обслуживанию

Результаты поиска

Содержание LWHD1200R

Отзывы:

Похожие инструкции для LWHD1200R

Бренды по названию

Популярные бренды