LG LV-1861HL Скачать руководство пользователя страница 23

Страница: 23 / 66

–23–

2. Indoor unit installation

■

Before Installing, prepare Installation Plates

• 'Installation Plates' are attached at the bottom of

indoor unit.
Detach them by removing each 3 screws at both
sides.

• Detach 'Side Plate (R,L)' by removing each 2 screws

on both sides.

• Pull the upper right and left side of 'Inlet Grille' to the

front, and it will stop at slightly tilted position.

• Unhook the 'Inlet hanger' from the 'Hanger screw' on

the both left and right side.

• Detach the 'Inlet Grille' from the Indoor Unit.

1) Installation on the ceiling

• Measure and mark the position for the Suspen-

sion bolts and the piping hole.

• Drill the hole for anchor nut on the ceiling.

※

Before secure the Installation Plates, select the bent
direction of the Installion Plate to the inside or the
outside according to the installation circumstances.

• Drill the piping hole on the wall slightly tilted to the

outdoor side using a ø70 hole-core drill.

1076

Suspension

bolt

Center-line for the

piping hole

265

1236

265

Install Plate

5~7mm

Indoor

Outdoor

WALL

Side Plate

Inlet Grille

Inlet hanger

Hanger

screw

Содержание LV-1861HL



































































Результаты поиска

Содержание LV-1861HL

Отзывы:

Бренды по названию

Популярные бренды

LG LV-1861HL, Руководство по обслуживанию

Результаты поиска

Содержание LV-1861HL

Отзывы:

Бренды по названию

Популярные бренды