background image

4

Ceiling Cassette Air Conditioner

Safety Precautions   

Do not modify or extend the
power cable.

• There is risk of fire or electric

shock.

Do not install, remove, or re-
install the unit by yourself
(customer).

• There is risk of fire, electric

shock, explosion, or injury.

Be cautious when unpacking
and installing  the product.

• Sharp edges could cause

injury. Be especially careful of
the case edges and the fins on
the condenser and evaporator.

For installation, always contact the dealer or an
Authorized Service Center.

• There is risk of fire, electric shock, explosion, or

injury.

Do not install the product on a defective installation
stand.

• It may cause injury, accident, or damage to the

product.

Be sure the installation area does not deteriorate
with age.

• If the base collapses, the air conditioner could

fall with it, causing property damage, product
failure, and personal injury.

Do not let the air conditioner run for a long
time when the humidity is very high and a door
or a window is left open.

• Moisture may condense and wet or damage

furniture.

Operation

Do not touch(operate) the
product with wet hands.

• There is risk of fire or electrical

shock.

Do not place a heater or other
appliances near the power
cable.

• There is risk of fire and electric

shock.

Do not let electric parts of the
product get wet.

• It may cause  There is risk of

fire, failure of the product, or
electric shock.

Use a vacuum pump or Inert (nitrogen) gas when doing leakage test or air purge. Do not compress air or oxygen
and do not use flammable gases. Otherwise, it may cause fire or explosion.

• There is the risk of death, injury, fire or explosion.

Содержание LT-C242PLE0






























Отзывы: