LG LT-C182QLE0 Скачать руководство пользователя страница 8

Страница: 8 / 38

Ceiling Cassette Air Conditioner

Installation

Installation of Indoor, Outdoor Unit

Selection of the best location

1) Indoor unit

• There should not be any heat source or steam

near the unit.

• There should not be any obstacles to prevent

the air circulation.

• A place where air circulation in the room will

be good.

• A place where drainage can be easily

obtained.

• A place where noise prevention is taken into

consideration.

• Do not install the unit near the door way.
• Ensure the spaces indicated by arrows from

the wall, ceiling, or other obstacles.

• The indoor unit must keep the maintenance

space.

2) Outdoor unit

• If an awning is built over the unit to prevent

direct sunlight or rain exposure, be careful that
heat radiation from the condenser is not
restricted.

• There should not be any animals or plants

which could be affected by hot air discharged.

• Ensure the spaces indicated by arrows from

the wall, ceiling, fence or other obstacles.

Unit:mm

Ceiling

Ceiling Board

300 or more

Above 2500

400 or less

1000

or more

500 or

300 or less

Floor

More than

300mm

Fence or

obstacles

More than 700mm

More than 600mm

More than

More than
300mmm

300mmm

More than
300mm

Sunroof

Please use an annexed sheet or the
corrugated cardboard on the bottom of
packing as installation sheet.

When using the bottom sheet, please use it
after separating the installation sheet from
packing of the product floor by using a knife
etc as a picture below.

Annexed sheet

Packing corrugated

cardboard on the

bottom

Содержание LT-C182QLE0







































Результаты поиска

Содержание LT-C182QLE0

Отзывы:

Похожие инструкции для LT-C182QLE0

Бренды по названию

Популярные бренды

LG LT-C182QLE0, Руководство по установке

Результаты поиска

Содержание LT-C182QLE0

Отзывы:

Похожие инструкции для LT-C182QLE0

Бренды по названию

Популярные бренды