LG LSWS306ST Скачать руководство пользователя страница 11

Страница: 11 / 28

- 11 -

ENGLISH

INSTALL THE OVEN

Part 4

CABINET INSTALLATION

The fifth step of the installation is to install the oven into the cabinet as follows:

1. Sliding the oven into the opening.

a. Loop (do not tie) a 36” (91 cm) string around the conduit before the oven is slid into place.This will keep the

conduit from falling behind the oven.

b. Lift oven into cabinet cutout using the oven opening as a grip. Carefully push against the oven front frame.

Do not push against outside edges.

c. While sliding the oven back, pull the string so that the conduit lies on the top of the oven in a natural loop.

d. When you are sure the conduit is out of the way, slide the oven 3/4 way back into the opening. Remove the

string by pulling on one end of the loop.

• DO NOT block the oven air exhaust

located at the bottom of the oven.

- Blocking the exhaust may cause cabinet damage

and product malfunction.

CAUTION

• Mounting screws must be used.

- Failure to do so can result in the oven falling out

of the cabinet causing serious injury.

WARNING

2. Securing the oven.

a. Using the mounting holes on the oven side trim as

a guide, drill pilot holes for screws provided (For

securing the double wall oven, use a minimum of

4 screws, one on each side in both the upper and

lower ovens. For securing the single wall oven, use

a minimum of 2 screws, one on each side.)

b. Secure the oven to the cabinet with screws

provided.

If the cabinet is particle board, you must use 3/4”

particle board screws. These may be purchased at

any hardware store.

3. Installing the metal bottom trim.

(For model : LWS3081ST, LWD3081ST, LWS3010ST, LWD3010ST)

a. Place the metal bottom trim centered over the pre-

drilled mounting holes on the lower base.

b. Using 3 screws provided, secure the bottom trim

to the bottom edge of the cabinet.

4. Reinstalling the oven door.

(For model :LWS3081ST, LWD3081ST, LWS3010ST, LWD3010ST)

Mounting

Hole

Locations

Mounting

Hole

Locations

Trim Screws

Side

Trim

Side Trim

Lower base

Metal Trim:

Correct

position

Metal Trim:

Wrong

position

Metal

bottom

trim

Step. 1

Firmly grasp both

sides of the door at

the top.

Step. 2

With the door at the

same angle as the

removal position, seat

the indentation of the

hinge arm into the

bottom edge of the

hinge slot. The notch

in the hinge arm must

be fully seated into the bottom of the slot.

Step. 3

Fully open the door. If the door will not fully open, the

indentation is not seated correctly in the bottom edge

of the slot.

Step. 4

Push the hinge locks up

against the front frame of

the oven cavity to the locked

position.

Step. 5

Close the oven door.

Hinge arm

Bottom
edge of
slot

Indentation

Hinge arm

Hinge lock

Содержание LSWS306ST





























Результаты поиска

Содержание LSWS306ST

Отзывы:

Бренды по названию

Популярные бренды

LG LSWS306ST, Руководство по установке

Результаты поиска

Содержание LSWS306ST

Отзывы:

Бренды по названию

Популярные бренды