ENGLISH
5
INSTALLATION
- The picture may differ from the actual product.
- Consult a professional installer prior to mounting the TV using a wall bracket.
1
How to Attach the Brackets for the Product to the TV
-
If the screw will not fully tighten when using a guide spacer, recheck the assembly depth of the screw and refer to the technical service
manual.
Guide spacer
Guide spacer screw
-
Work procedure
1. Check to see if the display has screws installed into
the mounting holes. If so, remove those.
2. Assemble the guide spacer and the guide spacer
screw in order as shown in the picture.
-
Place the TV on a table with the screen facing
down. Make sure that you place it on a flat
surface covered with a soft cloth or cushion to
protect it from scratches.
-
Secure the guide spacers to the TV with the
screws.Assemble the guide spacer to the set by
tightening the screw.Tighten the screw until the
set, guide spacer and the screw are fully pressing
against one another.
-
Use the + driver (manual or motorized) when
tightening the screw.
2
How to attach to masonry walls
Please follow the below direction.
-
Check the material of the wall and the thickness of the finishing.
-
Use the appropriate anchor for a concrete wall, and install them in a manner. That does not crack the wall.
-
Do not mount the device on the walls made from wood stud, plasterboard or medium density fiberboard (MDF). In this case, the
anchor and screws must be inserted into the concrete behind the finish surface. If there is no concrete on the other side, then you
must first install a separate hanger to securely install the anchors and screws.
-
When installing the product on wall material not designated, install the product so that each location can withstand the pull out load of
70 kgf (686 N) and shear load of 100 kgf (980 N) or above.
a
b
d
e
Wall mount screw
c
Anchor
-
Use the Ø 8 mm drill bit for concrete and hammer (Impact) drill.
a. Use a drill bit Ø 8 mm to drill a hole for the anchor location within a depth of 80 mm - 100 mm.
b. Clean the drilled hole.
c. Insert the sealed anchor to the hole. (When inserting the anchor, use a hammer.)
d. Set the wall mount on the wall by aligning to the location of the hole. and, set the angle adjusting part to face upward.
e. Align the wall mount bolt to the hole and tighten it. Then, fasten the bolts at torque of 45 kgf/cm - 60 kgf/cm.
3
How to install the wall mount
- Mount the product only on a concrete wall. LG Electronics Inc. is not liable for any accidents caused by mounting
the product on walls made of any other materials, including wood, plywood, and bricks.
Wall mount
screw
→
If the screw cannot be assembled in the designated
location inevitably, it can be assembled by
rearranging to the closest location. But, do not
change 2 or more locations from the designated spot.
→
Attach the right and left side with two bolts each.
→
At this time, use a + driver (manual or motorized) or
8 mm wrench to tighten the screw so that the wall, wall
bracket and screw are completely pressed against one
another.
4
How to assemble the wall mount support and display
- Always install the display with 2 or more people.
* Caution: Prevent the power cord from being pinched between the
wall mounting bracket and the set when installing the set.
(A pinched power cord may cause damage to the product.)
When inserting the guide spacer,
align its center with the arrow
shown in the figure for easy
installation.
→
After attaching the guide spacers to the set, hang it on the wall mounting bracket in the direction of the arrows. Attach the lower
part first, then attach the upper part by slightly lifting up the set.
-
Make sure that the product is attached securely by pulling on the bottom of the set.
-
When mounting the product that has a speaker, hold and lift up the product, not the speaker.
