background image

4

Installation method

1

  Fixating the mounting bracket on the TV

    If the screw will not fully tighten when using a guide spacer, recheck the assembly depth of the screw and 

refer to the technical service manual.  

- The actual product may differ from the picture. 

<Work procedure>

1.  Check to see if the display has screws installed into the 

mounting holes. If so, remove those. 

2.  Assemble the guide spacer and the guide spacer screw in 

order as shown in the picture.

   -   Assemble the guide spacer to the set by tightening the 

screw. 

   -  Tighten the screw until the set, guide spacer and the screw 

are fully pressing against one another. 

   -  Use the "+" driver (Manual or motorized) when tightening 

the screw. 

3

How to install the wall mount

<When installing on a masonry wall>

    When you separate the 8 screws on the wall mount connected to the wall bracket for use with a wooden wall, it is much easier 

to install the product. 

   When installing the product on a masonry wall, turn the 8 

screws  on  the  A  part  counterclockwise  to  separate  the 
screw and bracket.

   After  aligning  the  wall  bracket  to  the  location  to  install, 

mark  the  part  to  screw  on  the wall  and  then  remove  the 
wall bracket. 

  Refer to page 4 to attach the wall bracket.

  Use a level to check whether the wall mount is level.

Separate the wall mount screw.

2

How to attach to masonry walls

- Check the material of the wall and the thickness of the finishing.

- When installing the product on the wooden wall, refer to page 5. 

-  When installing the product on wall material not designated, install the product so that each fixated location can withstand 

the pull out load of 70kgf (686N) and shear load of 100kgf (980N) or above. 

-  Use the Ø8mm drill bit for concrete and hammer (Impact) drill.

Please follow the below direction.

a. Use a drill bit Ø8mm to drill a hole for the anchor location within a depth of 80mm ~ 100mm

b. Clean the drilled hole. 

c. Insert the sealed anchor to the hole. (When inserting the anchor, use a hammer.)

d. Set the wall mount on the wall by aligning to the location of the hole. and, set the angle adjusting part to face upward.
e. Align the wall mount bolt to the hole and tighten it. 

 

Then, fasten the bolts at torque of 45 - 60 kgf/cm.

Wall mount screw

Anchor

-  Tools you will need : Phillips head "+" driver(Manual or motorized) 

Ø4mm drill bit for wood or steel / Level / Stud finder / Drill. 

You may also need an 8mm socket wrench or an 8mm drill bit for concrete.

-  Use the anchors for wall material of concrete, light concrete, strong natural stone, soft natural stone masonry brick and 

hallow block that do not crack.

a

b

d

e

c

Guide spacer

screw

Guide spacer

Содержание LSW420BX









Отзывы: