LG LS090HXV2 Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 72

background image

64

Single Zone Mega and Mega 1

15V W

all Mounted Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.

©LG Electronics U.S.A., Inc., Englewood Cliffs, NJ. All rights reserved. “LG” is a registered trademark of LG Corp.

FINAL INSTALLATION PROCEDURES

Installer Mode

It will be necessary to switch to Installer mode if the system needs to operate in Heating Only or
Cooling Only modes, or the Pump Down procedure needs to be performed.

To Enter Installer Mode:

1. Press the Reset and “A” buttons. A very slender tool is needed to access the Reset button.

2. Set the code by pressing the Up and Down Temperature buttons, and then press the ON / OFF

button. The Up Temperature button changes the code on the ten (10) digit; the Down Temperature
button changes the code on the one (1) digit.

Press

SETUP

Figure 115: Using the Handheld Con-

troller to Change System to Installer

Mode.

Installer Mode, Cooling Only Mode

• After the system is in Installer mode (with Cooling Only mode initiated), automatic operation is suspended.
• After Cooling Only mode is disabled, the system will return to normal operation.
• Installer mode cannot be entered if the unit is running. The system must be completely OFF.
• All Installer code numbers must be entered when system is OFF.
• WLAN Module’s communication time will lag by about one (1) minute after unit is turned back on, and in normal operating mode.
• Entire lock or Mode lock cannot be set if heating or automatic operation is set through a central controller.

Disabling Cooling Only Mode

After Pump Down procedure has been performed, Cooling Only
mode will need to be disabled, and the system will need to be re-
turned to normal operating mode.
1. Supply power to the system, but system must be OFF with all

functions inactive.

2.  Enter the Installer mode.
3.  Set code to 43 for Mega (HEV2), or 46 for Mega 115V (HXV2).
4.  Press ON / OFF button and select the code number 43 for Mega

(HEV2), or 46 for Mega 115V (HXV2). Unit will beep to acknowl-
edge that code has been received.

5. Turn off power for a minimum of 30 seconds.
6. Turn power back on to system.

Enabling Cooling Only Mode

Before running the Pump Down procedure, the unit must be
switched to Cooling Only mode. To be able to run Cooling Only
mode, the unit must be changed to Installer mode (see previous
page for instructions).
1. Supply power to the system, but system must be OFF with all

functions inactive.

2.  Enter the Installer mode.
3.  Set code to 45 (for both Mega (HEV2) and Mega 115V HXV2).
4.  Press ON / OFF button and select the code number 45. Unit will

beep to acknowledge that code has been received.

5. Turn off power for a minimum of 30 seconds.
6. Turn power back on to system.

«
...
62
63
64
65
66
...
»

Содержание LS090HXV2









































































Отзывы:

Нет отзывов

Похожие инструкции для LS090HXV2

Бренд: NANO Страницы: 28

Бренд: Samsung Страницы: 52

Бренд: Fakir Страницы: 24

SkyAir FHQ18PVJU

Бренд: Daikin Страницы: 15

Бренд: Alfa Laval Страницы: 71

Бренд: S&P Страницы: 20

Бренд: Friedrich Страницы: 20

Бренд: Zibro Страницы: 2

Бренд: eeese Страницы: 94

Бренд: IDEAL Страницы: 65

Бренд: Refco Страницы: 8

Бренд: Daikin Страницы: 273

Бренд: TCL Страницы: 40

Бренд: Daikin Страницы: 13

Бренд: SANG Страницы: 42

Бренд: Panasonic Страницы: 16

Бренд: Panasonic Страницы: 22

Бренд: Panasonic Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды