background image

18

Safety Precautions

Operating Instructions

Care and Maintenance

Troubleshooting Tips

Care and Maintenance

Operating Instructions

Safety Precautions

Front panel

Panel hook

Air filters

Air filters

Gasoline

Powder

Indoor Unit

Care and maintenance of the air conditioner

CAUTION: Before performing any maintenance, turn off the main power to the system.

Never use any of the followings:

• Water hotter than 40°C

Could cause deformation and/or discoloration.

• Volatile substances

Could damage the surfaces of the air conditioner.

1. Lift the front access panel and pull the filter tab

slightly forward to remove the filter.

2. Clean the filter with a vacuum cleaner or warm,

soapy water.
• If dirt is conspicuous, wash with a solution of

detergent in lukewarm water.

• If hot water (40°C or more) is used, it may be

deformed.

3. After washing with water, dry well in the shade.

4. Re-install the air filter. 

1. After removing the air filters, pull slightly forward to

remove the PLASMA filter.

2. Dip the PLASMA filter into the water mixed with

neutral detergent, for 20~30 minutes.

3. Dry the PLASMA filter in the shade for a day

(Especially, the humidity must be removed
perfectly on this parts).

4. Note the cuts of electric discharge lines.

5. Re-install the PLASMA filter to the original position.

Open the upside of Front Panel

1

Relocate dried air filters at the shade and then

close the panel.

5

Put up the Front panel.
The hook of panel comes off.

2

Come down the panel and then remove 
air filters.

3

Do cleaning by soft brush and a vacuum
cleaner. If it has hard pollution, wash by
water.

4

Don’t touch this PLASMA Filter within 10
seconds after opening the inlet grille, it may
cause an electric shock.

Содержание LS-C142UBD0
























Отзывы: