background image

4

Floor Standing type Air Conditioner

Safety Precautions

Do not modify or extend the power cable.

• There is risk of fire or electric shock.

Be cautious when unpacking and installing  the
product.

• Sharp edges could cause injury. Be especially

careful of the case edges and the fins on the
condenser and evaporator.

For installation, always contact the dealer or an
Authorized Service Center.

• There is risk of fire, electric shock, explosion,

or injury.

Do not install the product on a defective
installation stand.

• It may cause injury, accident, or damage to

the product.

Be sure the installation area does not
deteriorate with age.

• If the base collapses, the air conditioner could fall with

it, causing property damage, product failure, and
personal injury.

Do not let the air conditioner run for a long time when
the humidity is very high and a door or a window is
left open.

• Moisture may condense and wet or damage

furniture.

Do not store or use flammable gas or combustibles near the product.

• There is risk of fire or failure of product.

Use a vacuum pump or Inert (nitrogen) gas when doing leakage test or air purge. Do not compress air or
Oxygen and Do not use Flammable gases. Otherwise, it may cause fire or explosion. 

• There is the risk of death, injury, fire or explosion.

n

Operation

Gasolin

Содержание LPUC808FA0





















Отзывы: