LG LP090CED-Y8 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 49

background image

- 36 -

Copyright ©2008 LG Electronics. Inc. All right reserved.
Only for training and service purposes

LGE Internal Use Only

Fuse Holder Kit

Part No: AYFH1101

Description

This optional fuse holder kit can be installed directly in the
chassis or in the optional subbase.
Fuse holder kits are available in 230/ 208 volt ratings. The
installer should supply time delay fuses at 15, 20, 25, or 30
amps in accordance with the Maximum Overcurrent
Protection as listed on the unit nameplate. Fuses may be
purchased from the parts department.

Note:

The installation and servicing of this equipment must be
performed by qualified, experienced technicians only.

WARNING

Hazardous Voltage!

Disconnect all electric power, including remote disconnects
before servicing. Follow proper lockout/ tagout procedures to
ensure the power can not be inadvertently energized. Failure
to disconnect power before servicing could result in death or
serious injury.

Important Note:

The unit OFF switch does not disconnect all electrical power
to this unit.

CAUTION

Use Copper Conductors Only!

Unit terminals are not designed to accept other types of
conductors. Failure to use copper conductors may result in
equipment damage.

Important Note:

All wiring must comply with applicable local and national
codes.
Type and location of fused disconnect switch(es) must
comply with all applicable codes. Failure to follow these
codes could result in overheating and equipment failure.

Receiving

Upon receipt of the product, inspect the shipping carton for
signs of visible damage. Report any damage or shortage to
the carrier and note it on the delivery receipt. Unit must be
stored in its original shipping carton in a dry, secure place
prior to its installation and use.

Installation

The installation and servicing of the equipment referred to in
this booklet should be performed by qualified, experienced
technicians.

Fuse Holder Kit Installation
(Without Subbase)

1. Remove front by rotating bottom outward and then lifting up

and out from chassis.

Mode Switch

Thermostat

Remove two screws
to gain access inside
Control Panel

Fuse Holder
Knockouts
under panel

Figure 48 - Control Panel

«
...
34
35
36
37
38
...
»

Содержание LP090CED-Y8


















































Отзывы:

Нет отзывов

Похожие инструкции для LP090CED-Y8

Бренд: Panasonic Страницы: 72

Бренд: Panasonic Страницы: 36

mini VRF U-4LE2R5

Бренд: Panasonic Страницы: 60

Бренд: Panasonic Страницы: 12

Бренд: Panasonic Страницы: 96

Бренд: Panasonic Страницы: 149

Бренд: Haier Страницы: 15

Бренд: ForestAir Страницы: 38

Бренд: GE Страницы: 36

Бренд: Waeco Страницы: 33

Бренд: Sakura Страницы: 16

Бренд: A.O. Smith Страницы: 16

Бренд: Unical Air Страницы: 49

Бренд: Airwell Страницы: 71

Бренд: Arctic King Страницы: 30

Бренд: AllerAir Страницы: 2

Бренд: BestAir Страницы: 14

Бренд: Daikin Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды