manualshive.com logo in svg

LG LMV2053SB - 2.0 Cu. Ft. Microwave, Руководство по обслуживанию

Поделиться
Скачать
LG LMV2053SB - 2.0 Cu. Ft. Microwave Скачать руководство пользователя страница 32

7-21

(3)  CHECKOUT PROCEDURES FOR CIRCUIT

BOARD

The following symptoms indicate a defective circuit
board.

1)  Check the input current. If the input current is more

than 20A, check the magnetron and wiring. If the
input current is less than 0.5 A, there is no input to
the H.V.T.

2)  The start function fails to operate but the high

voltage Systems, the interlock switches, the door
sensing and the relay check good.

3)  The unit with a normal relay continuously operates.
4)  The buzzer does not sound or continues to sound.

5)  Some segments of one or more digits do not light

up, or they continue to light up, or segments light
when they should not.

6)  Wrong figures appear.
7)  The figures of all digits.
8)  The clock does not keep time properly.

NOTE:

A MICROWAVE ENERGY LEAKAGE TEST MUST ALWAYS BE PERFORMED WHEN THE UNIT IS
SERVICED FOR ANY REASON.

Содержание LMV2053SB - 2.0 Cu. Ft. Microwave













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды