background image

– 1

4

 –

STEP 5: 

Install The Mounting Plate

C

B

A

The Oven Must Be Connected To At Least One

Wall Stud.

4. Attach the plate to the wall. To use spring toggle head bolts:

Remove the toggle wings from the bolts. Insert the bolts into

the mounting plate and replace the spring toggle head to 3/4

past the bolt ends. Insert the spring toggle head into the

holes in the wall to mount the plate. You may pull forward on

the plate to help in tightening the toggle bolts. Tighten all

bolts. See Figure 3

1

.

3. Remove the template from the rear wall.

1. Center the rear wall template in the space by lining up the

plumb line on wall with centerline on template.Then securely

tape or tack the rear wall template in place.Make sure the

minimum width is 30 inches and that the top of the rear 

wall template is located a minimum of 30 inches above

the cooking surface. See Figure 2

6

.

NOTE: If the cabinets are not plumb, adjust the rear wall

template to the cabinets. If the front edge of the

cabinet is lower than the back edge, adjust the

template to be level with the cabinet front.

a stud. If there is a stud, drill a 3/16  hole for lag screws.

If there is no stud, drill a 5/8  hole for toggle bolts. 

These holes must be used for mounting. If the holes are

not used, the installation will not be secure. Installer must 

use these holes for proper installation. See Figure 

30

.

Use toggle bolts through these holes, unless one of them

lines up with a stud. Use a wood screw for studs. 

Make sure to use at least 1 lag screw in a stud,

and 2 toggle bolts in the drywall or the plaster.

2. Drill holes at points A, B. Drill the third hole inside area C,

through one of the bottom holes to match the location of

NOTE: Cut out the shaded area marked F on the REAR

WALL TEMPLATE for wall-venting.

Figure 

3

1

Figure 

30

Wall

Mounting

Plate

Space More Than Wall Thickness

Bolt
End

Toggle Bolt

Toggle Wings

1

3/16

  

 Hole on Studs

5/8 

  

Hole on Drywall Only

Minimum 6

6

From the Floor

For Wall -

Vent

ing

 Only

Draw Lines
on Studs

Draw

Center Line

Center Line

Mounting Plate

Support Tab

Support Tab

Содержание LMHM2237BD/01

















Отзывы: