background image

28

UNDERSTANDING SOUNDS YOU MAY HEAR

Your new refrigerator might produce certain noises that 
your previous refrigerator did not. It is normal if you worry. 
Most of the new sounds you will be hearing are actually 
normal and expected. Hard surfaces like walls or floor 
can increase sounds and make them sound louder than 
they really are. The following list has a description of such 
sounds along with their causes.

• The thawing timer will make a “click” sound when such 

timer will start and finish. Temperature controlling 
device will also make a “click” sound at the beginning 
and ending of the refrigerator cycle.

• You will hear a bell sound caused by the flow of the 

refrigerant, water pipe or objects located on the superior 
part of the refrigerator.

• Your refrigerator is designed to work efficiently to 

preserve your food at the desired temperature using 
the least of energy. You will be able to hear a pulsing 
sound coming from the ventilators and the evaporator. 
The speed of the ventilator can speed up when you 
open the refrigerator door.

• After each cycle you will hear a dripping sound due to 

the refrigerant liquid in your refrigerator.

• Contraction and expansion of the inner walls can cause 

a slight popping sound.

• You will hear a dripping sound caused during the 

thawing cycle.

• During the defrosting cycle the water might cause a 

dripping sound.

• You can hear some tight air sound over the capacitor 

caused by the fan.

• Running water can be heard during the defrosting 

cycle.

• Due to its low energy consumption design of the 

refrigerator; the fans will remain of, while the on-off 
switch activated the internal light of bin.

Problem

Possible Causes

Solutions

THE REFRIGERATOR 

WON´T TURN ON

• The plug is correctly positioned.

• A fuse has gone bad or the circuit 

presents failures.

• The refrigerator is in the defrosting 

cycle.

• Firmly plug the cord into a live outlet with proper 

voltage.

• Replace the fuse or reset the circuit breaker.

• Wait about 30 minutes for defrost cycle to end.

THE DISPLAY 

SHOWS THE

WORD “OFF”

• Refrigerator is in Demo Mode. 

(Demonstration Mode)

• The Demonstration Mode disables the cooling 

system; only the lamps and display work 

normally.

• To disable open refrigerator doors and then 

press ICE PLUS       and REFRIGERATOR      

buttons at the same time for 5 seconds.

THE LIGHT WON’T 

TURN ON

• The refrigerator is plugged.

• The light bulbs are loose.

• A light bulb has gone bad.

• Plug the refrigerator in a right voltage plug.

• Unplug the refrigerator. Unscrew the Light bulb 

and screw it again (Read the section 

Refrigerator 

Care and Cleaning

). Plug again.

• Unplug the refrigerator before changing the 

light bulb. Replace the bulb with a same 40 

watts bulb for your local store. (Read the section 

Replacing Refrigerator Lights

).

TROUBLESHOOTING GUIDE

Содержание LFC25765 Series

































Отзывы: