background image

IMPORTANT:

Please read carefully.

TO CONNECT ELECTRICITY

RECOMMENDED GROUNDING METHOD

The refrigerator should always be plugged into its own
individual properly grounded electrical outlet rated for 
115 Volts, 60 Hz, AC only, and fused at 15 or 20 amperes.
This provides the best performance and also prevents
overloading house wiring circuits which could cause a fire
hazard from overheated wires. It is recommended that a

separate circuit serving only this appliance be provided.
Use a receptacle which cannot be turned off with a switch
or pull chain. Do not use an extension cord.

Where a standard two-prong wall outlet is encountered, 
it is your personal responsibility and obligation to have it
replaced with a properly grounded three-prong wall outlet.

Do not, under any circumstances, cut or remove the
third (ground) prong from the power cord.

NOTE:

Before performing any type of installation,

cleaning, or removing a light bulb, turn the control
(Thermostat, Refrigerator Control or Freezer Control,
depending on the model) to OFF and then disconnect the
refrigerator from the electrical source. When you are
finished, reconnect the refrigerator to the electrical source
and reset the control (Thermostat, Refrigerator Control or
Freezer Control, depending on the model) to the desired

setting.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain
conditions, we strongly recommend against the use of
an extension cord.

However, if you still elect to use 

an extension cord, it is absolutely necessary that it be 
a UL-listed (in the United States), 3-wire grounding type
appliance extension cord having a grounding type plug
and outlet, and that the electrical rating of the cord be 15
amperes (minimum) and 120 volts.

Use of an extension cord will increase the clearance
needed for the back of the refrigerator.

WARNING

Electrical Shock Hazard

FOR PERSONAL SAFETY,

this appliance must be

properly grounded. Have the wall outlet and the
circuit checked by a qualified electrician to make sure
the outlet is properly grounded.

Ensure proper
ground exists 
before use.

3-prong
grounding
plug

3-prong
grounding type
wall receptacle

Your old refrigerator may have a cooling system that used

If you are throwing away your old refrigerator, make sure

CFCs (chlorofluorocarbons). CFCs are believed to harm

the CFC refrigerant is removed for proper disposal by a

stratospheric ozone. 

qualified servicer. If you intentionally release this CFC
refrigerant, you can be subject to fines and imprisonment
under provisions of environmental legislation.

DANGER:

RISK OF CHILD ENTRAPMENT

BEFORE YOU THROW AWAY
YOUR OLD REFRIGERATOR
OR FREEZER

Take off the doors.

Leave the shelves in place so that 
children may not easily climb inside.

CFC DISPOSAL

GROUNDING REQUIREMENTS

Child entrapment and suffocation are not problems of
the past. Junked or abandoned refrigerators are still
dangerous... even if they will sit for “just a few days”. If
you are getting rid of your old refrigerator, please follow
the instructions at right to help prevent accidents.

This appliance contains fluid (refrigerant, lubricant), is
made of parts and materials which are reusable and / or
recyclable. All the important materials should be sent to 
the collecton center of waste material and can be reused
after rework (recycling). 
For take back, please contact with the local agency. 

6

WARNING

 

POWER CORD REPLACEMENT

 

If the power cord is damaged, it must be replaced
by the manufacturer, by our service center or by
qualified personal by LG Electronics, to avoid some
risk.

Содержание LFC20740 Series





































Отзывы: