LG LDS4821 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 43

background image

- 15 -

- 15 -

Fan Assembly

Inner Cover

Gasket

Flange

Hose

Detergent

Dispenser

Door Hinge

Air Duct

Door Bracket

Hinge Bracket

Hinge Spring

3) Fan Assembly

Open the door.
Remove 4 screws and a earth screw for

Door Bracket.
Remove the wire connetions.
Remove the Air Duct.
Turn the Inner Cover counterclockwise.

4) Detergent Dispenser

Close the door

Remove the wire connections.
Remove 6 screws with brackets.
Push the Detergent slowly pulling up the

the Flange by Standard Screwdriver.

5) Door Spring (Right & Left)

Push the Spring upwards and take it off

from the Hinge Bracket.

Be careful not to be injured by the

sharpedge of Tub.

Take off the Hinge Link from the Hinge.

6) Door Liner

Open the door.
Pull the Door Liner and take it off from

the Hinge Supporter.

Door Liner Assembly

Hinge Supporter

«
...
12
13
14
15
16
...
»

Содержание LDS4821












































Отзывы:

Нет отзывов

Похожие инструкции для LDS4821

Бренд: GE Страницы: 5

Бренд: Haier Страницы: 10

Бренд: Haier Страницы: 29

Бренд: Haier Страницы: 8

Бренд: Haier Страницы: 21

Бренд: Haier Страницы: 18

Бренд: Haier Страницы: 2

Бренд: Haier Страницы: 16

Бренд: Hansa Страницы: 2

Бренд: Hansa Страницы: 2

Бренд: Samsung Страницы: 5

HFC 3T232 WFG X UK

Бренд: Hotpoint Страницы: 8

Бренд: Fisher & Paykel Страницы: 56

SINGLE DISHDRAWER DD24SCTX9

Бренд: Fisher & Paykel Страницы: 3

Бренд: Galanz Страницы: 14

Бренд: minibaby Страницы: 9

AdoraDish V6000

Бренд: V-ZUG Страницы: 60

DCS DishDrawer DD24DUT7

Бренд: Fisher & Paykel Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды