LG LCS1410SW Скачать руководство пользователя страница 27

Страница: 27 / 36

5-16

CONDITION

CHECK

RESULT

CAUSE

REMEDY

(TROUBLE 5) No microwave oscillation even though oven lamp and fan motor run.

(Display operates properly)

No microwave
oscillation.

No continuity.

Continuity.

Disconnect the
wire leads from
relay 2 and
check continuity
of relay2.
(Operate the unit)

Defective PCB
assembly

Defective high
voltage
transformer.

Replace PCB
assembly

Output is full power
when you set lower
power level.

Abnormal.

Disconnect the
wire leads from
relay 2 and check
continuity relay 2.
(Operate the unit)

Defective PCB
assembly

Replace PCB
assembly

Replace high
voltage
transformer.

Defective high
voltage capacitor.

Replace high
voltage capacitor.

Abnormal

normal

Check high vol-
tage transformer

Abnormal

normal

Check high vol-
tage capacitor.

Defective high
voltage diode.

Replace high
voltage diode.

Abnormal

normal

Check high vol-
tage diode.

Defective
magnetron.

Replace
magnetron.

Abnormal

Check
Magnetron.

NOTE: • Make sure the wire leads are in the correct position.

• When Removing the wire leads from the parts, be sure to grasp the connector, not the wires.
• When removing the magnetron, be sure to install the magnetron gasket in the correct position

and in good condition.

Содержание LCS1410SW





































Результаты поиска

Содержание LCS1410SW

Отзывы:

Похожие инструкции для LCS1410SW

Бренды по названию

Популярные бренды

LG LCS1410SW, Руководство по обслуживанию

Результаты поиска

Содержание LCS1410SW

Отзывы:

Похожие инструкции для LCS1410SW

Бренды по названию

Популярные бренды