LG LB-E4880 Series Скачать руководство пользователя страница 3

Страница: 3 / 24

ENGLISH

1. The following should be always observed for safety

• Please report to or take consent by the supply authority before connecting to the system.
• Be sure to read "THE FOLLOWING SHOULD BE ALWAYS OBSERVED FOR SAFETY" before

installing the air conditioner.

• Be sure to observe the cautions specified here as they include important items related to safety.
• The indications and meanings are as follows.

• After reading this manual, be sure to keep it together with the owner's manual in an accessible

place.

Could lead to death, serious injury, etc.

Do not install it yourself (customer).

Perform the installation securely referring to the

installation manual.

Install the unit securely in a place which can bear the

weight of the unit.

Perform electrical work according to the installation

manual and be sure to use an exclusive circuit.

Attach the electrical part cover to the indoor unit and

the service panel to the outdoor unit securely.

Be sure to use the part provided or specified parts for

the installation work.

Check that the refrigerant gas do not leak after
installation is completed.

Perform the drainage/piping work securely

according to the installation manual.

Use the specified wires to connect the indoor and the

outdoor units securely and attach the wires firmly to

the terminal board connecting sections so the stress

of the wires is not applied to the sections.

• Incomplete installation could cause injury due to fire, electric shock,

the unit falling or a leakage of water. Consult the dealer from whom
you purchased the unit or special installer.

• Incomplete installation could cause a personal injury due to

fire, electric shock, the unit falling or a leakage of water.

• When installed in an insufficient strong place, the unit could fall

causing injured.

• Incomplete connecting and fixing could cause fire.

• If the capacity of the power circuit is insufficient or there is

incomplete electrical work, it could result in a fire or an electric
shock.

• The use of defective parts could cause an injury or leakage of

water due to a fire, electric shock, the unit falling, etc.

• If there is a defect in the drainage/piping work, water

could drop from the unit and household goods could be
wet and damaged.

Do not install the unit in a place where an

inflammable gas leaks.

• If gas leaks and accumulates in the area surrounding the unit, it

could cause an explosion.

• If the electrical part cover if the indoor unit and/or the service

panel if the outdoor unit are not attached securely, it could result
in a fire or electric shock due to dust, water, etc.

Could lead to serious injury in particular environments when operated incorrectly.

WARNING

CAUTION

Do not install the electric heater

• Electric heater may cause deformation or fire of blower

and housing which were made of plastic.

Содержание LB-E4880 Series

























Результаты поиска

Содержание LB-E4880 Series

Отзывы:

Похожие инструкции для LB-E4880 Series

Бренды по названию

Популярные бренды

LG LB-E4880 Series, Руководство по установке

Результаты поиска

Содержание LB-E4880 Series

Отзывы:

Похожие инструкции для LB-E4880 Series

Бренды по названию

Популярные бренды