LG LB-C482ESG0 Скачать руководство пользователя

Страница: 24 / 27

Ceiling Duct Type Air Conditioner

Air Purging of the Connecting Pipes and the Indoor Unit

Air Purging of the Connecting Pipes and the Indoor Unit

The air which contains moisture remaining in the refrigeration cycle may cause a malfunction on the
compressor.

1. Confirm that both the liquid side valve and the gas side valve are set to the closed position.

2. After connecting the piping, check the joints for gas leakage with gas leak detector.

3. Remove the service port nut, and connect the gauge manifold and the vacuum pump to the

service port by the charge hose.

4. Vacuum the indoor unit and the connecting pipes until the pressure in them lowers to below -

76cmHg.

5. Remove the valve stem nuts, and fully open the stems of the 2-way and 3-way valves with a

hexagon wrench.

6. Tighten the valve stem nuts of the 2-way valve and 3-way valve.

7. Disconnect the charge hose and fit the nut to the service port.

(Tightening torque: 1.8kg.m)

Indoor unit

Outdoor unit

Liquid side

OPEN

Vaccum pump

Gas side

Closed

2-way valve/

3-way valve

3-way

valve

Содержание LB-C482ESG0




























Результаты поиска

Содержание LB-C482ESG0

Отзывы:

Похожие инструкции для LB-C482ESG0

Бренды по названию

Популярные бренды

LG LB-C482ESG0, Руководство по установке

Результаты поиска

Содержание LB-C482ESG0

Отзывы:

Похожие инструкции для LB-C482ESG0

Бренды по названию

Популярные бренды