LG LB-C306GSS0 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 35

background image

Installation Manual

25

ENGLISH

Connecting Cables between Indoor Unit and Outdoor Unit

Form the pipings

• Wrap the connecting portion of indoor unit with

the Insulation material and secure it with two
Plastic Bands. (for the right pipings)

- If you want to connect an additional drain

hose, the end of the drain-outlet should keep
distance from the ground. (Do not dip it into
water, and fix it on the wall to avoid swinging
in the wind.)

• Tape the Pipings, drain hose and Connecting

Cable from bottom to top.

• Form the pipings gathered by taping along the

exterior wall and fix it onto the wall by saddle
or equivalent.

• Tape the Pipings and Connecting cable from

bottom to top.

• Form the pipings gathered by taping along the

exterior wall, and make the trap prevent water
from entering into the room.

• Fix the pipings onto the wall by saddle or

equivalent.

Trap is required to prevent water from entering
into electrical parts.

Seal a small opening
around the pipings
with gum type sealer.

Drain hose

Taping

Pipings

Connecting
cable

Power supply
cord

Seal a small opening
around the pipings
with gum type sealer.

Trap

Trap

In case of the Outdoor unit being installed
below position of the Indoor unit.

In case of the Outdoor Unit being installed
above position of the Indoor Unit.

«
...
23
24
25
26
27
...
»

Содержание LB-C306GSS0




































Отзывы:

Нет отзывов

Похожие инструкции для LB-C306GSS0

Бренд: Valeo Страницы: 15

IND-AHC-TRF-2X2-UVC-R1-120V

Бренд: Larson Electronics Страницы: 3

Бренд: mundoclima Страницы: 9

Бренд: Hiyasu Страницы: 14

LU-VE Arctigo ISD

Бренд: Alfa Network Страницы: 32

Бренд: Aprilaire Страницы: 32

Бренд: London Cool Страницы: 3

Бренд: King Industrial Страницы: 6

bycool green line LITE

Бренд: dirna Bergstrom Страницы: 64

QuietMaster SL25

Бренд: Friedrich Страницы: 24

Бренд: Daikin Страницы: 84

Бренд: Viking Страницы: 2

23-23-0258N-013 s

Бренд: Fedders Страницы: 31

VRV-WII FXYCP10MY1

Бренд: Daikin Страницы: 35

Бренд: Danby Страницы: 36

Бренд: Qlima Страницы: 130

Бренд: Daikin Страницы: 14

Бренд: Panasonic Страницы: 481

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды