LG L5UC728FA0 Скачать руководство пользователя страница 7

Страница: 7 / 59

Installation Manual

Installation of Indoor, Outdoor Unit

Installation of Indoor, Outdoor Unit

Read completely, then follow step by step.

1. Indoor unit

• Do not have any heat or steam near the unit.

• Select a place where there are no obstacles in

front of the unit.

• Make sure that condensation drainage can be

conveniently routed away.

• Do not install near a doorway.

• Ensure the spaces indicated by arrows from

the wall, ceiling, fence or other obstacles.

• Use a stud finder to locate studs to prevent

unnecessary damage to the wall.

Install the air conditioner in the location that
satisfies the following conditions.

• The place shall easily bear a load exceeding

four times the indoor unitʼs weight.

• The place shall be able to inspect the unit as

the figure.

• The place where the unit shall beleveled.

• The place shall allow easy water

drainage.(Suitable dimension “H” is necessary
to get a slope to drain as figure.)

• The place shall easily connect with the

outdoor unit.

• The place where the unit is not affected by an

electrical noise.

• The place where air circulation in the room will

be good .

• There should not be any heat source or steam

near the unit

Select the best location

More than 20 cm

More than

10 cm

More than 2.3 m

More than

10 cm

More than 20 cm

More than 10 cm

More than

10 cm

600

Top view

(unit: mm)

Front view

Front

Inspection Hole

(600X600)

Inspection Hole

(600X600)

Control box

1000

CAUTION: Install the indoor unit
on the wall where the height from
the floors more than 2.3 meters.

Wall mounted Type

Duct Type

Содержание L5UC728FA0




























































Результаты поиска

Содержание L5UC728FA0

Отзывы:

Похожие инструкции для L5UC728FA0

Бренды по названию

Популярные бренды

LG L5UC728FA0, Руководство по установке

Результаты поиска

Содержание L5UC728FA0

Отзывы:

Похожие инструкции для L5UC728FA0

Бренды по названию

Популярные бренды