LG HT552TH Скачать руководство пользователя страница 8

Страница: 8 / 62

1-7

SPECIFICATIONS

GENERAL

Power supply

Refer to main label.

Power consumption

Refer to main label.

Net Weight

3.6 kg

External dimensions (W x H x D)

430 x 70 x 311 mm

Operating conditions

Temperature: 5°C to 35°C, Operation status: Horizontal

Operating humidity

5% to 85%

Laser

Semiconductor laser, wavelength 650 nm

CD/DVD

Signal system

PAL 625/50, NTSC 525/60

Frequency response (audio)

200 Hz to 18 kHz

Signal-to-noise ratio (audio)

More than 75 dB (1 kHz, NOP -6 dB, 20 kHz LPF/A-Filter)

Dynamic range (audio)

More than 70 dB

Harmonic distortion (audio)

0.5 % (1 kHz, at 1W position) (20 kHz LPF)

VIDEO

Video input

1.0 V (p-p), 75 Ω, negative sync., RCA jack x 1

Video output

1.0 V (p-p), 75 Ω, negative sync., RCA jack x 1/ SCART (TO TV)

COMPONENT VIDEO OUT

(Y) 1.0 V (p-p), 75 ohms, negative sync, RCA jack x 1
(PB)/(PR) 0.7 V (p-p), 75 ohms, RCA jack x 1

TUNER
FM

Tuning Range

87.5 - 108.0 MHz or 65.0 - 74.0 MHz, 87.5 - 108.0 MHz

Intermediate Frequency

10.7 MHz

Signal-to Noise Ratio

60 dB (Mono)

Frequency Response

140 - 8,000 Hz

AM [MW]

Tuning Range

522 - 1,620 kHz or 520 - 1,720 kHz

Intermediate Frequency

450 kHz

AMPLIFIER

Stereo mode

70 W + 70 W (4Ω at 1 kHz, THD 10 %)

Surround mode

Front: 70 W + 70 W (THD 10 %)
Center*: 70 W
Surround*: 70 W + 70 W (4Ω at 1 kHz, THD 10 %)
Subwoofer*: 150 W (3Ω at 30 Hz, THD 10 %)

Inputs

AUDIO IN, OPTICAL IN

Outputs

MONITOR OUT, EURO AV (TO TV) OUT
COMPONENT VIDEO OUT

SPEAKERS

Front/Rear Speaker

Center speaker

Passive Subwoofer

(SH52TH-S)

(SH52TH-C)

(SH52TH-W)

Type

2 Way 3 Speaker

1 Way 1 Speaker

Impedance

4 Ω

3 Ω

Frequency Response

100 - 20000 Hz

150 - 20000 Hz

40 - 1500 Hz

Sound Pressure Level

82 dB/W (1m)

80 dB/W (1m)

Rated Input Power

70 W

150 W

Max. Input Power

140 W

300 W

Net Dimensions

(W x H x D)

260 x 1100 x 260 mm

330 x 86 x 121 mm

212 x 395 x 341 mm

Net Weight

3.0 kg

1.15 kg

6.0 kg

(* Depending on the sound mode

settings and the source, there may
be no sound output.)

Содержание HT552TH































































Результаты поиска

Содержание HT552TH

Отзывы:

Бренды по названию

Популярные бренды

LG HT552TH, Руководство по обслуживанию

Результаты поиска

Содержание HT552TH

Отзывы:

Бренды по названию

Популярные бренды