background image

4

Location and Function of Controls

Software

Install the appropriate CD Recording Authoring Software before using this unit. 
* Please uninstall any previous CD burning software you may have loaded on your PC in
order to prevent possible compatibility issues. Once you have installed the application 
software, you may (if you wish) begin to reinstall previous software, taking note for errors.
We recommend using the drive with the latest software as some problems encountered
when using the drive can be solved by updating the software.

Front Panel

1. Digital Audio Output Connector

This connector is not supported.

2. Analog Audio Output Connector
3. Jumper Connector

This jumper determines whether the drive is 
configured as a master or slave. Changing the
master-slave configuration takes effect after
power-on reset.

4. IDE Interface Connector

Connect to the IDE (Integrated Device
Electronics) Interface using a 80-pin flat IDE
cable.

NOTE :

Do not connect or disconnect the cable

when the power is on, as this could cause a
short circuit and damage the system. 
Always turn the power OFF when connecting or
disconnecting this cable.

5. Power Connector

Rear Panel

1. Disc Tray

2. Emergency Eject Hole

3. Stop/Eject Button

4. Drive activity indicators

The LED used to indicate the operation of

Super Multi DVD Rewriter

.

1

2 3

4

1 2 3   4      5

Содержание GSA-H44N
















Отзывы: