manualshive.com logo in svg

LG GR-459GTCA, Руководство по обслуживанию

Поделиться
Скачать
LG GR-459GTCA Скачать руководство пользователя страница 11

- 11 -

4. FAN AND FAN MOTOR

1) Remove freezer drawers.

2) Remove two cap, screws and loosen two screws in

Grille Fan.

3) Pull out the Grille Fan and Shroud, F.

4) Disconnect the housing of lead wire.

5) Separate the Fan Assy.

6) Losse 2 screw fixed to the Bracket.

7) Pull out Shroud, F remove the Fan Motor Assy.

8) Separate the Motor Bracket and Rubber.

5. DEFROST CONTROL ASSY

Defrost Control Assy consists of Thermistor and Fuse,
Melting. Thermistor functions to defrost automatically and it
is attached to metal side of the Evaporator and senses
temperature.

Fuse, Melting is a kind of safety device for preventing
overheating of the Heater when defrosting. 

At the temperature of 77°C, it stops the emission of heat
from the Heater.

1) Pull out the Shroud, F after removing the Grille.

2) Separate the connector connected with the Defrost

Control Assy and replace new one.

6. HEATER, SHEATH & HEATER, CORD-L

In this refrigerator, Heater, Sheath & Heater, Cord-L are
used for defrosting heater. During heating, the temperature
of heater rises about 300~350°C. Therefore, be careful not
to burn while servicing.

1) After removing the Grille and Shroud, separate the

Heater, Sheath by disconnecting the connectors.

2) Exchanged Heater, Sheath and connected the housing.

3) If the Heater, Cord-L is defected, disconnect the

connectors, and separate the Heater, Cord-L with 
Long Nose.

4) Replace and assembly the Heater, Cord-L and connect

the connectors.

Heater, Sheath

Heater, Cord-L

GUIDE FAN

FAN

SHROUD

FAN MOTOR

GRILLE

Thermister

Fuse, Melting

Figure  13

Figure  11

Figure  12

Содержание GR-459GTCA





























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды