LG GoldStar MS-110YG страница 22 Скачать руководство пользователя | Manualshive

Страница: 22 / 35

background image

5-12

1. Incomplete segments.

• Segment missing.
• Partial segment missing.
• Digit flickering (NOTE: Slight flickering is normal.)

2. Colon does not turn on or blink.
3. A distinct change in the brightness of one or more numbers in display.
4. One or more digits in the display are not lighting.
5. Display indicates a number different from one touched, for example, key in

5

and

3

appears in the display.

6. Specific numbers (for example 7 or 9) will not display when key pad is touched.
7. Display does not count down with time blinking or up with clock operation.
8. Display obviously jumps in time while counting down.
9. Display counts down too fast while cooking.

10. Each indicator light does not turn on after setting cooking cycle.
11. Display time of day does not reappear when cooking is finished.

(TROUBLE 1) The following visual conditions indicate a probable defective control circuit.

CONDITION

CHECK

RESULT

CAUSE

REMEDY

1. No input can be

programmed.

Continuity

No continuity

Defective PCB
assembly.

Loose
connection.

Replace PCB
assembly.

Connect them
tightly.

Check the conn-
ection between
membrane key
assembly and
PCB assembly.

2. Some inputs

cannot be
programmed.

3. Display shows a

number or figure
different from one
touched.

4. Random

programming
when touching
other pads.

5. Display is fixed

at some figure
and can not
accept any
input.

Everything works
as specified.

Still have trouble.

Defective key
membrane
assembly.

Defective PCB
assembly.

Replace key
membrane
assembly.

Replace PCB
assembly.

Replace key
membrane
assembly and
check operation.

«
...
20
21
22
23
24
...
»

Содержание GoldStar MS-110YG




































Отзывы:

Нет отзывов

Похожие инструкции для GoldStar MS-110YG

Бренд: Candy Страницы: 14

Бренд: Daewoo Страницы: 25

Modernist Microwave In-A-Drawer DMR24M977WM

Бренд: Dacor Страницы: 28

Бренд: Master Chef Страницы: 32

Бренд: Parmco Страницы: 18

Бренд: Bartscher Страницы: 88

Бренд: Fama Страницы: 24

Бренд: Stilevs Страницы: 24

Gorenje BOP747ORAW

Бренд: ORA ITO Страницы: 52

Бренд: Gaggenau Страницы: 32

IC 60 3MP W 343C

Бренд: VALBERG Страницы: 146

Бренд: NEFF Страницы: 3

Бренд: Doyon Страницы: 57

Бренд: GE Страницы: 2

Ultra Bake UB-E4T

Бренд: Nu-Vu Страницы: 2

Бренд: AEG Страницы: 48

Бренд: KitchenAid Страницы: 16

Бренд: KitchenAid Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды