background image

6-5 SERVICE DIAGNOSIS CHART

- 15 -

In addition to the items described above, refer to the followings to solve the complaint.

Check if dew forms
in the Freezer.

Replace the
Components of
defrosting circuit.

Check Refrigerating
Cycle.

Check the
Thermostat.

Defrosting is poor.

The cycle is faulty.

Repair the cycle.

Replace the
Thermostat.

The operation of the
Thermostat is poor.

COMPLAINT

POINTS TO BE CHECKED

REMEDY

Cooling is

 Is the power cord unplugged from the outlet?

 Plug to the outlet.

impossible.

 Check if the power S/W is setted to OFF.

 Set the switch to ON.

 Check if the fuse of power S/W is shorted.

 Replace a regular fuse.

 Measure the voltage of power outlet.

 If voltage is low, wire newly.

Cooling ability

 Check if the set is placed close to wall.

 Place the set with the space of about 10cm.

is poor.

 Check if the set is placed close to stove, gas

 Place the set apart from these heat sources.

¥

 

cooker and direct rays.

 Is the ambient temperature high or 

 Make the ambient temperature below.

¥

 

the room door closed?

 Check if putting in hot food.

 Put in food after they get cold.

 Did you open the door of the set too often 

 Don't open the door too often and close

¥

 

or check if the door is closed up?

¥

 

it firmly.

 Check if the TEMP. CONTROL is set to MIN.

 Set the knob to MID.

Freezing ability

 Is the ambient temperature too LOW(10 C)?

 For colder freezer, turn the 

FREEZERTEMP.

is poor

¥

 

CONTROL to "6"~"7", and the REFRIGERATOR

TEMP. CONTROLto  MAX.

 Check if the FREEZERTEMP. CONTROL

 Turn the TEMP. CONTROL to 3~6. 

is set to 1~2?

Food in the

 Are food placed in cooling air outlet?

 Place food in high temperature section.

Refrigerator

¥

 

(Front Part)

are frozen.

 Check if the TEMP. CONTROL is set to MAX.

 Set the knob to MID.

Dew or ice

 Are watery food kept?

 Seal up watery food with vinyl wrap.

forms in the

 Check if putting in hot food.

 Put in food after getting cold.

chamber of

 Did you open the door of the set too  

 Don't open the door too often and close

the set.

often or check if the door is closed up.

¥

 

it firmly.

Dew forms

 Check if ambient temperature and humidity

 Wipe dew with a dry cloth. This happening

in the Out Case.

are high.

¥

 

is solved in low temperature and humidity

¥

 

naturally.

 Is the gap in the door packing?

 Fill up the gap.

Abnormal

 Is the set positioned in a firm and even place?

 Adjust the Leveling Screw, and place

noise generates.

¥

 

in the firm place.

 Does any unnecessary objects exist 

 Remove the objects.

¥

 

in the back side of the set?

 Check if the Cover Evaporating Tray is omitted.

 Place it on an original position.

 Check if the cover of mechanical room 

 Place the cover at an original position.

in below and front side is taken out.

To close the door

 Check if the door packing becomes dirty 

 Clean the door packing.

is not handy.

¥

 

by filth such as juice.

 Is the set positioned in a firm and even place?

 Position in the firm place and adjust the

¥

 

Leveling Screw.

 Are too much food put in the set?

 Keep foods from reaching to the door.

Ice and food

 Check if the inside of the set becomes dirty.

 Clean the inside of the set.

smell unpleasant.

 Did you keep smelly foods without wraping?

 Wrap smelly food.

 It smells plastic.

 The new products smell plastic, but it is

Содержание GN-U192SL





















Отзывы: