LG GB115 Скачать руководство пользователя страница 18

Страница: 18 / 142

Bus Interconnections

The interconnection between the X-Bus and the TEAKlite Bus uses:

• Multicore Synchronization

• Shared Memory.

3.1.6 Clock Concept

The X-GOLDTM102 has a flexible clock control.

3.1.7 Interrupt Concept

The C166 MCU carries out the X-GOLDTM102 interrupt system.

3.1.8 Debug Concept

The X-GOLDTM102 includes a multi-core debug. The C166 and TEAKlite cores can be debugged

in parallel with:

• A single JTAG port (that is, on a single host)

• Mutual breakpoint control.

C166 Debug Concept

The debugging of the C166 uses the OCDS and the Cerberus.

The X-GOLDTM102 also inlcudes a Real Time Trace module for software debugging.

TEAKLite Debug Concept

TEAKlite debugging uses the OCEM and the SEIB.

3.1.9 Power Management

The X-GOLDTM102 provides the power management unit (PMU) for the complete mobile phone

application. The integrated PMU is directly connected to the battery and provides a set of linear

voltage regulators (LDO’s). These LDO’s generate all required supply voltages and currents

needed in a low feature mobile phone.

The charger unit controls the charging of NiCd, NiMh, LiPolymer and LiON batteries. Only a few

external parts are required to support charging from a DC wall adaptor. In addition, the charger

generates the power-on reset after battery insertion or charger connection. The supported battery

voltage range is 3.1 to 5.1 V for NiCd/NiMH and 3.1 to 4.6 V for LiPolymer and LiON batteries. The

upper voltage limit is programmable.The charger supports constant current precharging,

full-charging (pulsed charging) and software controlled constant current charging. The charging

functions are protected by hardware timer. Charger idle voltages up to 20 V can be handled. An

integrated overvoltage protection protects batteries and system against overvoltage.

White/blue backlight generation is supported with a special driver for very a low external parts

count. Power consumption during operation phases is minimized due to flexible clock switching

In the Standby Mode most parts of the device are switched off, only a small part is running at

32kHz and the

controller RAM is switched to a power saving mode. The TEAKLite ROM can be switched off

during Standby via SW.

This Units (associated to the Measurement Unit) provides also support for a accessory

detection .

Содержание GB115















































































































































Результаты поиска

Содержание GB115

Отзывы:

Похожие инструкции для GB115

Бренды по названию

Популярные бренды

LG GB115, Руководство по обслуживанию

Результаты поиска

Содержание GB115

Отзывы:

Похожие инструкции для GB115

Бренды по названию

Популярные бренды