LG CM9530 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 87

background image

NOTES REGARDING HANDLING OF THE PICK-UP

1. Notes for transport and storage

1) The pick-up should always be left in its conductive bag until immediately prior to use.
2) The pick-up should never be subjected to external pressure or impact.

2. Repair notes

1) The pick-up incorporates a strong magnet, and so should never be brought close to magnetic materials.
2) The pick-up should always be handled correctly and carefully, taking care to avoid external pressure and

impact. If it is subjected to strong pressure or impact, the result may be an operational malfunction and/or
damage to the printed-circuit board.

3) Each and every pick-up is already individually adjusted to a high degree of precision, and for that reason

the adjustment point and installation screws should absolutely never be touched.

4) Laser beams may damage the eyes!

Absolutely never permit laser beams to enter the eyes!
Also NEVER switch ON the power to the laser output part (lens, etc.) of the pick-up if it is damaged.

5) Cleaning the lens surface

If there is dust on the lens surface, the dust should be cleaned away by using an air bush (such as used
for camera lens). The lens is held by a delicate spring. When cleaning the lens surface, therefore, a cotton
swab should be used, taking care not to distort lens.

6) Never attempt to disassemble the pick-up.

Spring has excess pressure. If the lens is extremely dirty, apply isopropyl alcohol to the cotton swab.
(Do not use any other liquid cleaners, because they will damage the lens.) Take care not to use too much
of this alcohol on the swab, and do not allow the alcohol to get inside the pick-up.

Storage in conductive bag

Drop impact

NEVER look directly at the laser beam, and don’t allow
contact with fingers or other exposed skin.

Magnet

How to hold the pick-up

Conductive Sheet

Cotton swab

Pressure

Pressure

1-3

SERVICING PRECAUTIONS

«
...
2
3
4
5
6
...
»

Содержание CM9530
























































































Отзывы:

Нет отзывов

Похожие инструкции для CM9530

Бренд: GE Страницы: 28

Бренд: Bartec Страницы: 46

Бренд: D-Link Страницы: 6

Бренд: Oklahoma Sound Страницы: 2

Бренд: Oklahoma Sound Страницы: 13

Бренд: Pacific Sun Страницы: 12

Бренд: Panasonic Страницы: 2

Total Solutions TSS-800

Бренд: Infinity Страницы: 26

Бренд: Laser Страницы: 9

Бренд: Pyle Страницы: 8

Бренд: M-system Страницы: 5

Smarty 4X P 1.1

Бренд: Salda Страницы: 30

IntelliGate 2025

Бренд: Aastra Страницы: 71

Бренд: Icare Страницы: 27

Бренд: JBL Страницы: 16

Бренд: CAME Страницы: 16

Бренд: FARFISA INTERCOMS Страницы: 2

Бренд: Soundstream Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды