LG AVNQ36GM2T1 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 24

background image

19

ENGLISH

INSTALLATION INSTRUCTIONS

CAUTION

Installer setting mode is to set the detail function of the remote controller.

If the installer setting mode is not set correctly, it can cause problems to the product, user
injury or property damage. This must be set by an certificated installer, and any installation or
change that is carried out by a non-certificated person should be responsible for the results.

In this case, free service cannot be provided.

!

Refer to the Installer Setting Code Table
on the next page.

1. With the JET MODE / COOL button pressed,

press the RESET button.

2. By using the TEMPERATURE SETTING

button, set function code and setting value.

(Please refer the Installer Setting Code Table.)

3. Press the ON/OFF button toward the indoor

unit 1 time.

4. Reset the remote controller to use the general

operation mode.

INSTALLATION INSTRUCTIONS

Installer Setting - How to enter installer setting mode

°C/°F (5 s)

TIME (3 s)

1,MFL70699801,영어 2018. 6. 27. 오후 4:07 페이지 19

«
...
17
18
19
20
21
...
»

Содержание AVNQ36GM2T1

























Отзывы:

Нет отзывов

Похожие инструкции для AVNQ36GM2T1

Бренд: Bard Страницы: 8

Бренд: York Страницы: 24

Бренд: York Страницы: 56

Бренд: York Страницы: 385

AG TN1DKH Series

Бренд: Samsung Страницы: 22

Бренд: Data Aire Страницы: 64

Бренд: Data Aire Страницы: 123

Бренд: Eaton-Williams Страницы: 10

Бренд: Jafanda Страницы: 6

Бренд: iGenix Страницы: 9

Бренд: Hessaire Страницы: 8

Бренд: BASETech Страницы: 12

Бренд: Klarstein Страницы: 132

ROOFTOP FLEXY FCA 100

Бренд: Lennox Страницы: 142

Бренд: Zibro Страницы: 166

Бренд: Nortek Страницы: 12

PROFESSIONAL XL INN-560

Бренд: INNOLIVING Страницы: 28

Бренд: ICP Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды